Quantcast
Jump to content


Help disconnecting locker cable

Nickb1907

By Nickb1907
in Joyner UTV SxS Forum

 Share

Recommended Posts

Nickb1907 Rookie

Nickb1907

Posted
Posted

I tried searching for this and looking through the manual before I posted. I can't seem to figure out how to disconnect the cable from the pin coming out of the differential. I need to disconnect it to install the U shaped bracket that bolts to the diff that the cable goes through for the locker. My rear didnt have anything there.

BTW i modeled up and did a drawing on the bracket based off the the front. If yall have a bracket that everyone could use, I can model it up, do a drawing and anyone could take it to a local welding shop and have it made. See attached bracket.

post-1749-0-01388700-1358878730_thumb.png

Link to comment
Share on other sites
Guest Lenny

Guest Lenny

Posted
Posted

If you look closely, you will see a slot on the side of the pin. Youhave to rotate the cable to the side to line the cable u p with the slot and it will slide out. Its a bit of a pain to put back on with the bracket. What cad program are you using? I used to use autocad but for the last several years have used Solidworks.

Lenny

Link to comment
Share on other sites
Nickb1907 Rookie

Nickb1907

Posted
  • Author
Posted
If you look closely, you will see a slot on the side of the pin. Youhave to rotate the cable to the side to line the cable u p with the slot and it will slide out. Its a bit of a pain to put back on with the bracket. What cad program are you using? I used to use autocad but for the last several years have used Solidworks.

Lenny

Solidworks, but i have used all the others. We build frac equipment at work so i have access to all the fab stuff.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Ridge Runner
      2019 Coleman 550 Outfitter, need help accessing tail gate latch screws
      By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • Hunterman22
      Hisun Axis 500-700 Service Manual (2020 Version)
      By Hunterman22
      View File Hisun Axis 500-700 Service Manual (2020 Version)
      This is the 2020 updated version from the previous 2009 version.  I do not know all the differences.  I do know the 2020 models have throttle body , idle air control valve, & idle control sensor. 
      HS700UTV-4/HS500UTV-4 Hisun Axis 500-700 Service Manual 
      Submitter Hunterman22 Submitted 08/10/2024 Category Hisun  
    • sxr951
      2015 massimo 700.. need cylinder bolt!
      By sxr951
      2015 massimo 700.. need cylinder bolt!  it some special cut from factory,, its a 125 thread but its like between 8 and 10 mm  dont know where to find any ideas? thx
    • Stan Morton
      2018 Sidekick starter needs replacement ~ Looking for an alternative starter
      By Stan Morton
      My 2018 XG-850-SL starter died yesterday. The old part number from Kubota is E7153-11732 which has been superceed by part # EG881-63010. I am looking for an aftermarket starter because the Kubota retail price for the starter starts at $550 and upwards toward $850.  If anyone has gone down this road before and has found an aftermarket starter ~ please share with me. We own a ranch and this thing is used every single day and is sorely missed when it is down for maintenance.  Kind Regards, ~ Stan

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...