Quantcast
Jump to content


Recommended Posts

Posted

Looking at the lack of options that are off the rack. Finding more headache than I care too. I was wondering about doing this type of swap. has anyone attempted/done this what the result were? I have 2012 T2 and my wheels are 4x108mm (4.25in). I can't find crap. I do more on and off-road with the T2( I'm street legal) due to hunting and such. So I was looking to upgrade.

Sorry I have not been active like I should: moved, kitchen remodel, table saw with fingers.......couldn't do a whole lot of computer time.

Posted

Same bolt pattern as my Wildcat or at least I thought. My the trooper wheel fits right on the wildcat, but the lugs are larger on the trooper so the wildcat wheels don't fit on the trooper.

Posted

so if your 2012 has 4 by 108 and my 2008 has 4 by 115, when did they change, 2012 I presume.

How about posting a close up photo of a 2012 wheel, maybe even tape a ruler to the wheel for the photo,

Posted

Here are the pics. of the rear wheels and with tape held close to it. Had to start at 2inches due to fingers. Only had one good hand, but 2 to 5 1/4 still equals 4 1/4(or 108mm). Please correct me is my math is off. I may not be the sharpest tool in the shed but I can still do work.

post-1734-0-64591800-1373704897_thumb.jpg

post-1734-0-54726000-1373704899_thumb.jpg

Posted

Hi 2Scoops, what is the size of Wildcat tire, do you think there is enough metal there to drill the holes bigger if you wanted them on a Trooper and what about the back side spacing.

Kinarfi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By boydog40
      my subaru gave it up, bought a new Predator 670cc
      problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
      new motor has many more wires than the Subaru and i have no idea what goes where!!!
      finding any info on the web is almost impossible to do also
      any help will be greatly appreciated!
      thanks guys
    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?
×
×
  • Create New...