Quantcast
Jump to content


temp gauge

dedub

By dedub
in Joyner UTV SxS Forum

 Share

Recommended Posts

Kinarfi Veteran

Kinarfi

Posted
Posted

explain please

what happened to the temp sensor that was there, is it gone, it sends a signal to the computer so that the computer can adjust the fuel to the temperature.

https://www.dropbox.com/s/561djpqwan1re88/1100%20Trooper%20T2%20ECU%20Wiring%20Diagram.pdf

find A08 in the above file, if you want to take a chance on burning a hole in the piston by running too lean, you could substitute a resistor, but I would suggest putting the original back and find a different place for your manual gauge.

dedub Collaborator

dedub

Posted
  • Author
Posted

the old one quite working i took it out it broke doing so. i retaped the head to standard thread for maunal gauge. will a small rezester work? an do i power that pin?

Kinarfi Veteran

Kinarfi

Posted
Posted

It has been a long time since I messed with my temperature sensor, but I think it may have been 2 sensors in one, one for the computer and one for the gauge, if I remember correctly, you can measure the resistance from terminal to terminal and from terminal to ground.

I don't know how or if the computer uses these readings, except to guess that if the computer thinks the engine is hot, maybe it dumps lots of fuel into it trying to keep it cooler, or if it thinks the engine is cold, it richens the mixture for easier ignition. I do not know. and I don't know what value of resistor to suggest.

I guess my suggestion would be to buy a new standard sensor and figure out how to put it back in.

Kinarfi Veteran

Kinarfi

Posted
Posted

When you get the new one, can you take some measurements?

First, do you have a good Ohm meter? If so, can you measure the resistances of terminal to terminal and each terminal to case while in a bath of ice water, then while in boiling water or hot oil if you have a way to measure the temperature,

Guest Lenny

Guest Lenny

Posted
Posted

The computer does need the temp sensor to work correctly.

Lenny

  • 3 weeks later...
dedub Collaborator

dedub

Posted
  • Author
Posted

Dave, Did you get it fix what did you do?

NO NOT YET i put new temp sencor in did not help . but i didn't wire the gauge back up. so i'm going to put gauge back in an see what happens,

  • 2 weeks later...
Tinman Community Regular

Tinman

Posted
Posted

The computer does need the temp sensor to work correctly.

Lenny

Which sensor Lenny - the one at the head or the one on the radiator at the bottom?

I took the Rad one out and put my temp sensor there, and have had no running issues at all. Hopefully I pulled the right one...

Guest Lenny

Guest Lenny

Posted
Posted

Which sensor Lenny - the one at the head or the one on the radiator at the bottom?

I took the Rad one out and put my temp sensor there, and have had no running issues at all. Hopefully I pulled the right one...

The one in the heads is the one that the computer is interested in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • MMaster
      temp gauge
      By MMaster
      does anyone know of a replacement temp gauge that will work on a joyner 2016 r4, my gauge has condensation in it and it quit working
    • MMaster
      temp gauge
      By MMaster
      looking for a replacement  temp gauge that will work with my joyner r4 
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Ridge Runner
      2019 Coleman 550 Outfitter, need help accessing tail gate latch screws
      By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...