Quantcast
Jump to content


power steering

t2lizzard

By t2lizzard
in Joyner UTV SxS Forum

 Share

Recommended Posts

t2lizzard Contributor

t2lizzard

Posted
Posted

looking at installing power steering on my trooper, I know there are a few different makes of universal electric PS kits out there. does anyone have any recommendations on which unit works best / worst ? and if there are any tricks to making the install easier ?

t2lizzard Contributor

t2lizzard

Posted
  • Author
Posted

I have looked at SUPER ATV and UNISTEER. the SATV kit is almost half price of the UNISTEER kit. that's why I ask about quality etc. too much difference in price IMO. not sure what to make of it. how long have you had the one from SATV Kinarfi?

Kinarfi Veteran

Kinarfi

Posted
Posted

a couple of years at least, I don't know why the unisteer is so much, the satv has increased in price since I got mine, it works well and the only times is doesn't have enough power is in 4x4 & locker. Other than that, it's been good. If you order one, get the 220W model, there are several different mount methods on this site and the ujoints supplied do not match the trooper spline pattern so you have to do some creative matching. I suppose both units have this problem. I was just looking at the satv polaris ranger set up and it may have parts that work with joyners, call them and see what they offer.

dedub Collaborator

dedub

Posted
Posted

a couple of years at least, I don't know why the unisteer is so much, the satv has increased in price since I got mine, it works well and the only times is doesn't have enough power is in 4x4 & locker. Other than that, it's been good. If you order one, get the 220W model, there are several different mount methods on this site and the ujoints supplied do not match the trooper spline pattern so you have to do some creative matching. I suppose both units have this problem. I was just looking at the satv polaris ranger set up and it may have parts that work with joyners, call them and see what they offer.

kinarfi i took my trooper to super atv an let them us mine to make all brackets they were desiening new bigger motor for them at that time..

Kinarfi Veteran

Kinarfi

Posted
Posted

kinarfi i took my trooper to super atv an let them us mine to make all brackets they were desiening new bigger motor for them at that time..

That's probably the 220 watt job instead of the 170 watt, think I'll call them and see what I have and and if I can get the higher wattage motor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • SouthernGypsy
      Help needed, Anyone recognize where this Internally Threaded Bolt belongs?
      By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • se3388
      Anyone else with a UT10X?
      By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • John M in Louisiana
      Hisun E1 Power Plug Replacement
      By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...