Quantcast
Jump to content


1994? Mule 2500

norseman

By norseman
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

norseman Newbie

norseman

Posted
Posted

Hello

New to the forum.

I rescued what I was told was a 1994 2500 from rusting away next to a barn. Was told the motor runs but has water in the oil. I found some numbers stamped on the cross tube under the dash but all I can make out is KAF620C the longer number above is so faded it is not ledgeable. I have check other area but cannot find anything else.

Engine has a spline shaft. Need to try to verify the year.

Thank you

  • 3 months later...
xcycle Rookie

xcycle

Posted
Posted

The VIN on Mules are usually on a plate mounted to the frame at the front of the vehicle(mine is hard to see but is just to the left of the the plastic radiator cover) or sometime on frame near the middle of the seat.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • ToughLuck
      2021 Massimo MXU 1000 Runs Rich
      By ToughLuck
      I have a 2021 Massimo MXU 1000.  Last winter the front drive shaft sheared off inside the motor and it was cheaper to buy a new motor than to take it apart in order to remove the front drive shaft that was broken inside the case…
      Now it is running rich, seems to maybe be geared too high, does not accelerate well once you hit about 28mph.  I’ve replaced the O2 sensor.  MAF is next (I accidentally ordered the wrong one, but when I removed the old one you can clearly smell fuel).  
       I’m not a motorhead but I can turn a wrench.  Any ideas how to get this motor optimized?  The motor has about 300 miles on it.  I broke it in as recommended in the manual. 
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CSM_Retired
      Kioti UTV SxS Forum
      By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...