Quantcast
Jump to content


Recommended Posts

Posted

I put my order in for differential a couple of days ago and I didn't buy any of these because when I told people 200.00 they didn't want them. But if some one wants one I can get it. Usually takes 20 days.You would still need to get your third lever that's about 100.00 for it.

LOCKING DIFFERENTIAL MECHANISM
ITEM NO. PARTS CODE PARTS NAME QTY
.
1 .02.6183,1-M8/05 LOCK NUT M8 2
2 .02.2842-M8/05 FLANGE NUT M8 1
3 .S800.03.01.07 RELEASE LEVER MOUNT 1
4.01.5787-M8x20/05 FLANGE BOLT M8x20 2
5 .JD.1082101 RUBBER COVER 1
6.TR1100.03.01.06A DIFFERENTIAL LOCKING HANDLE 1
7 .DLJ.REV-33 RELEASE LEVER 1
8 .DLJ.REV-36 SPACER 1
9 .01.70,1-M8x60/05 HHCS BOLT M8x60 1
10 .JD.1092004 LEVER MOUNT CABLE RETAINE 1

12 .01.5787-M6x12/05 FLANGE BOLT M6x12 2
13 .S800.03.01.0002 CABLE BRACKET 1

15 .TR1100.03.01.05A FRONT LOCKER CABLE 1

  • Like 1
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Travis M
      Just purchased a T-Boss 760 and before putting any miles on it I'm going over all the fluids, grease and problem areas that I've read about online because I know the factory quality control is garbage. 
      I've seen where everyone seems to have leaking axle seals after 2-300 miles on the T-Boss 550 and 760. I think I'm going to switch from the bellow-style diff breather to the automotive style diff breather that they use on my Tacoma and various other vehicles. I'll still keep it extended and infact run it even higher, probably into the air intake box, but I'm hoping this is what's causing the axle seal leak issue on these vehicles.  
      I'll do the modification and report back every couple hundred miles and let you know. I currently only have 8 miles, so it will be a few months before I find out if mine leaks like everyone elses. 
    • By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
    • By dave pasch
      Has anyone trouble shooted this transfer case? Full 12v to switch and case. No action inside case.
       
      Thanks Dave
    • By hdtran
      That's the question! Or, if you want to add details:
      (a) How do you use the UTV? (roads? off-road to get to trees? etc.)
      (b) If you are wearing a helmet--how frequently? What type of helmet?
       
      My own answers: (a) Most of the time off-road to get to downed trees, cut the trees to logs and haul the logs back for splitting. (b) Very rarely, a ski helmet and not a motorcycle helmet.
    • By Hunterman22
      View File Hisun Axis 500-700 Service Manual (2020 Version)
      This is the 2020 updated version from the previous 2009 version.  I do not know all the differences.  I do know the 2020 models have throttle body , idle air control valve, & idle control sensor. 
      HS700UTV-4/HS500UTV-4 Hisun Axis 500-700 Service Manual 
      Submitter Hunterman22 Submitted 08/10/2024 Category Hisun  
×
×
  • Create New...