Quantcast
Jump to content


Random questions

charlie

By charlie
in Joyner UTV SxS Forum

 Share

Recommended Posts

charlie Experienced

charlie

Posted
Posted

Hey guys had the trooper out over the weekend 210 miles when in the white mtns of nh right up to the canada border beutifull landscapes up there! No issues with the trooper but got some questions cause I am not use to driving the trooper at 30-40 miles an hour for extended periods of time

Mine is an 09 1200 miles on it when should I do the t-belt

When your cruising along do any of you guys get gear type noise from your tranny not when accelerating but like at a steady speed easing in and out of the throttle my tranny has always been on the louder side the fluid is clean and I just changed it before the trip should I but a heavier grade oil in??

And I also notices I was getting a light rattle noise from I believe the front almost like as if u had two wrenches and were lightly tapping them together it came and went the noise I also noticed if I put my foot on the brake a little it stopped. Can't imagine it's a wheel bearing but maybe the brake pads rattling??

Thank Charlie

Link to comment
Share on other sites
rocmoc Grand Master

rocmoc

Posted
Posted

Yes my tranny always made noise when cruising down the road. If you are refering to the fan belt, it is fine. It will out last the rest of the Trooper. The clicking upfront on mine was the brake pads. Didn't bother me as my race cars always did the same thing. The Trooper doesn't have the little clips you install to stop the noise.

rocmoc n AZ/Mexico

Link to comment
Share on other sites
charlie Experienced

charlie

Posted
  • Author
Posted

thanx rocmoc and dan. I was talking about the actual t-belt behind the cover I know in the auto industry typically last 90,000-100,000. The noise I think is the brakes I will be pulling it apart this week to check. yes the tranny cruising down the road is when I hear it. The tranny like i said has always been loud just wanted to make sure it was normal cause I usually dont use 4th and 5th gears around home

Link to comment
Share on other sites
Kinarfi Veteran

Kinarfi

Posted
Posted

Not so sure the noise is tranny, I think it may be the differential and I've had a noisy machine for several years and 16000+ kilometers, wish I could eliminate it, but can't, the front brakes do have slop in them an I always here a small slap every time it step on the brakes.

Link to comment
Share on other sites
  • 4 weeks later...
charlie Experienced

charlie

Posted
  • Author
Posted

Hey guys found the rattle noise in the front end some of it I believe was the brake pads so I put some anti seize lube on the outside of them and I found the one of the hyme joints at the rack had gotten little loose so I greased it and tightened it and no more noise

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Clayton Walker
      Im New here but just got my Uforce Fitted for Hunting Season
      By Clayton Walker
    • Browner010
      2022 Coleman outfitter 500 had a loud snap then a metallic grinding noise
      By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • Dennis
      bd 300 bulldog shifting issues
      By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • KidColeman
      New 2020 Coleman Outfitter UT400 Owner with questions
      By KidColeman
      Hi All,
      Just picked  up a 2020 UT400 that my 80 year old father will be driving around the farm.  We purchased the machine with a few "issues" and they lowered the price accordingly.  Small stuff like passenger size mirror and back reflector was torn off by a Tractor supply employee, which we will order replacements for.  Also after further inspection, whoever assembled it did not put a few bolts in the rollcage and aren't in the glovebox, so will be having to order those also.
      Anyway, there are two initial things on the UT400 I'm not sure what they are or for.  The first, there is a square white electrical connector with about 8 pins hanging form under the middle of the back bed - I don't see another one to match up or plug into it, so wondering if this is pre installed optional connection for like towing around a sprayer?  Anyone know what this is?  Also, there is a 10 inch black rubber hose that is zip tied to the back A frame on the passenger side.  I watched the assembly video and it doesn't mention one, so don't know what this hose is for - anyone know?
      Also, has anyone come up with a "fix" or work around for having to have the seatbelts plugged in or even in place?  We aren't planning on using them and are figuring just plugging them in and wedging them behind the seats - didn't know if there is a way to just disconnect the "over 10mph gas starving" safety sensor.
      Looking forward to seeing how this machine does for my father.   I'm thinking about installing a suicide knob on it for easier turning for him, as it's a little stiff (compared to our Kawasaki Mule).  Maybe with use it will loosen up some?
      Thanks!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...