Quantcast
Jump to content


Recommended Posts

Posted

Hi folks just purchased a 08 renegade the guy said he put newwireing harness on it but couldn't get it started any one with a good diagram or how tos no start no wire to fuel pump no power a ecu??? Thanks

Posted

Thanks plumber found out mine it updated to the 09 wiring harness so far I have most engine relays getting power fuses good but the wire for starter silinoid not sure the only wire there is yellow with a round connection not push on type also my new ecu is sparking if touches frame my fuel pump not coming on on key switch 4 wires big red wire hot small red white stripe hot purple wire not hot white wire not hot?

Posted

Purchased this new harness jmcmotors i have checked for polarity on fuse relay panel 4 out of 6 fuses don't have polarity (fan fuel ignition guages) in 2009 Manuel it shows 7 fuses in panel not 6 but this harness has 6 1 relay has no polarity (fan)the gages don't cycle no power fuel pump no power starter silinoid? I don't know if this harness will work

Posted

Update found a black wire that need to be on positive now all fuses are working still no start and gauges are not cycling like before ? Fuel pump still not working does any have a clue what it is I think I'm close.

Posted

Update found cut wire in new harness what gives ?gages light up cycle over mph tach working no oil no volts no temp ?? And it idles nice no high end power? Any help appreciated ??? Any one there?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Nutcase
      I have a Joyner Trooper 1100 4 place that has been sitting for a number of years. I have everything taken care of but i can't get the fuel through the injectors. Fuel pump puts full pressure on them but they don't turn on or spray fuel. Any ideas?
    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
×
×
  • Create New...