Quantcast
Jump to content


Wheel Bearing and Loctite update + CV grease

Kinarfi

By Kinarfi
in Joyner UTV SxS Forum

 Share

Recommended Posts

Kinarfi Veteran

Kinarfi

Posted
Posted

I had a roller bearing fail, it sounded like I had rocks being crushed and ground,

When I took it apart, I found the Loctite I used did it's job excellently, I had to heat the outer race which was still firmly locked in place till I blued it with an acetylene torch and then drive it out with hammer and punch.

I didn't notice this problem until the second time I noticed the smell of brakes or clutch, maybe 100 Km. When i checked, my wheel was so hot, I couldn't touch it, trailer time!!! The bearing had allowed hub to tilt and it rubbed the brake pads rather hard and heated up, it was smoking when I stopped. The delay in noticing the problem allowed the hub to wear against the bearing and it created a slight ridge on the inner part of where the hum meets the bearing which I ground off being careful not to grind on the flat part where the bearing seats.

In the process of replacing bearing, when I pulled the outer CV, the axle, only, came with it, I exposed the outer CV joint and the grease around it appeared to have dried up, I added a bunch of new grease and it moved freely again in all directions.

I installed a used ball bearing that I had cleaned and grease and I'm up and running and have no wobble in either of my rear wheels.

I like the yellow loctite and I like roller bearings!!

Jeff

  • Like 1
Kinarfi Veteran

Kinarfi

Posted
  • Author
Posted

Well, it's already back together and running, the " used" one the was replaced by a roller bearing which was the first to be loctited into place, so I don't have any photos, sorry. The inner races of the ball bearing can be popped out which is what I did to clean them and re-grease them. When I come to wheel bearing, I believe in having spares on hand. It sure paid off to have saved the old ones and I was lucky that I had the correct seal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Browner010
      2022 Coleman outfitter 500 had a loud snap then a metallic grinding noise
      By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • sxr951
      anyone ever have to beat your starter out with a hammer till it broke in half?.lol
      By sxr951
      corrosion had its oring neck area  jammed in.. and besides that had corrosion in the starter just shorted when ran direct jumper cable to the starter post power to it

    • Joe Breaux
      still going
      By Joe Breaux
      just an update on my MSU 500 . For all the misery it caused me the first 2 yrs, and the combination of some quality YAMAHA parts, it has now become a reliable ,useful UTV without the constant fear of having to push or tow it back from trails. I have not had a single issue pop up in a very long time.. FINALLY!....and as a side note, I just bought  a C FORCE 600 ATV to replace an old and well used  Honda that finally after 18 yrs gave up a rod bearing.  So far the new one has really impressed me .. I like the new Power Steering and  this CVT Auto Trans is new to me on an ATV .. I m used to constant shifting on my Hondas .  It also has something I have never seen. Its EBS  engine brake system, as soon as you let go of throttle, it engine brakes you to a stop rather quickly.. its great idea for the grandkids safety . Takes a little getting used to tho.. All in all, I like it. We shall see how durable it is after break-in.. I do "RIDE" them! .....and they honor their warrenty! and the dealer is 15 minutes away.. 
    • The Road Hound
      Which UTV?
      By The Road Hound
      Hi, 
      New to the forum. 
      Came here looking for some experienced UTV users who can enlighten me about which brand should I pick for my very first UTV or SXS. 
      I'm between 3 brands and 3 models: 
      *Kawasaki MULE PRO-FXR   1000.
      *Yamaha wolverine rmax2. 
      *Can am Commander XTP. 
      The use I'm willing to give it is mostly to go to the range with my wife, load steel targets and all our shooting gear, we shoot a lot, rifles, Shotguns and Handguns for practice, training and competition. (Range is about 10 miles from home) 
      But also I want something that I can take to the trails and have fun on dirt, mud, rocks, puddles or creeks. 
      Any objective information will be appreciated, specially which is more reliable and durable. 
      Thank you and happy 4th of July. 
       
    • johnpeter
      RZR 1000 XP EPS - Rocks & Trails Edition 2020
      By johnpeter
      RZR 1000 XP EPS - Rocks & Trails Edition 2020 On Ebay
      https://www.ebay.com/itm/355474995514?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...