Quantcast
Jump to content


Steering Box

plumber

By plumber
in Joyner UTV SxS Forum

 Share

Recommended Posts

hfrick Enthusiast

hfrick

Posted
Posted

also curious as to what happened...steering rack updates with a new upper plate or changing out to the most current steering box is what I have seen....we have been putting power steering into the newer/updated boxes without trouble...that box does look kinda cool tho....Hardy

plumber Proficient

plumber

Posted
  • Author
Posted

What happened to the old one?

Hit a tree with the front tire blow off the top of the steering box. Dedub has done a subaru steering in he's it drives real nice but it rides even better he added a shock and left the stock one's in. Rides a lot better than mine.

Kinarfi Veteran

Kinarfi

Posted
Posted

what parts are damaged is the plate still straight did it just strip out the screws if it just stripped out the screws you can fix that with a helicoil kit I think a helicoil repair is stronger than the original

Guest Lenny

Guest Lenny

Posted
Posted

Re-drill ant tap a size larger. On the steering box above, 1.5:1 sounds awful fast for the trooper. If I'm right, that would be only about 135 degrees of steering wheel turn from stop to stop. Stock is about 2 turns and its still hard to turn. I had 3 turns from stop to stop on mine and it helped a lot. I don't think the power steering would be enough to push the 1.5:1 box.

plumber Proficient

plumber

Posted
  • Author
Posted

Re-drill ant tap a size larger. On the steering box above, 1.5:1 sounds awful fast for the trooper. If I'm right, that would be only about 135 degrees of steering wheel turn from stop to stop. Stock is about 2 turns and its still hard to turn. I had 3 turns from stop to stop on mine and it helped a lot. I don't think the power steering would be enough to push the 1.5:1 box.

Thanks Yes I can re tap But I was just looking to see whats out there. Lenny those cams are on the money with the new intake and fuel controller it runs real good the wife said my be to good since I hit the tree. I would like to see some else do the intake I thought it was better than the fuel controller. All 1100cc Chery motors have them on them except the trooper and that were I think is were you lose power at. On my air/fuel gauge it went from 11 when I start it to a 11.6 is what it will read when I start it now.. the part # is 472-1008013

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • CYJSP2009
      2022 brandnew Joyner CV Axles and CV Joint rebuild kits are comming
      By CYJSP2009
      Dear Friends, 
      2022 Brand new Joyner CV Axles and CV  Joint rebuild kits are comming 
      1.  S650.03.02.02.00 ---Joyner 650 Commando Rear
      2. TR1100.03.01.03.00 --- Joyner Trooper Front 
      3. TR1100.03.02.03.00 --- Joyner Trooper Rear
      4. D650.03.02.02.00 --- Joyner 650 Sand Spider Rear Left 
      5. D650.03.02.03.00--- Joyner 650 Sand Spider Rear Right 
      6. SV800.03.02.01.00 --- Joyner 800 Viper, SV1100 Drive shaft Left
      7.  14274 --- 650 ider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      8. 15803  ---  650 Sand Spider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      Attached are the part photos for reference. 
      Above parts are now on the way to USA, will be ready for inland delivery in middle of July. 
      Price: CV Axle: USD250/ Piece;  CV Joint kit （without grease): USD110  send to door. 
      There will be special discount availabe for deals completed within July 2022.  
      Buy 1 piece: Get 5% discount, 
      Buy 2 pieces: get 10% discount.
      Buy 3 pieces: get 15% discount, 
      Buy 4 and more than 4 pieces: get 20% discount. 
      Please kindly note Qty for each part is not big  and it is hard to forcast when there will be next offer for these kind of products unless there is sufficient confirmed order qty for productioin arrangement. 
      Payment method: Payoneer payment link ( can pay through bank account or credit card) or Paypal ( [email protected]) .  Payment commission paid by the buyer. 
      Interested parties, please contact [email protected]. 
      Thanks
      Good Luck
      Casey / Leaf Asia
      July-07-2022
       
       
       














    • carl baney
      2021 Tracker 800sx DUMP BOX
      By carl baney
      have a 2021 tracker 800sx noticed locks on box when u fasten both sides of box are cracked anyone else have this probl
    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...