Quantcast
Jump to content


UTV Portal Box's - Gearbox information for RZR-Can-Am UTV's.


Recommended Posts

I have seen a few variations of the new Gear Reduction Box's Has anyone tried the new UTV Solutions Gear Reduction box's or portal box as some say. From what I am seeing the GRB provides 4” of lift by moving the axle centerline upwards by 4” at the wheel hub, allowing for greater ground clearance under the axle center. By moving the axle centerline, we’re able to maintain factory positions and angle measurements on the upper and lower control arms, Axle shafts, and tie rods.

The GRB also provides a wider stance, adding approximately 3” to each side. The wider stance allows you to go over or around the well-beaten path left by other UTVs and ATVs

DSC08491.JPG

DSC08490.JPG

DSC08492.JPG

Click here for full information on the polaris gear reduction box - portal boxes for rzr - can-am-yamaha-honda utv's!!

Link to comment
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Yes that price would be for the RZR 570. If we could get our hands on a Joyner it wouldn't be that hard to make a box for them as well. We would just need to know spline count on the axle and caliper mounts for it. I would think it would be that much more for it just time and effort. I never knew there was such a demand for custom Joyners out there...

Link to comment
Share on other sites

  • 6 months later...
Guest WillieOi

LEDOS- Производство светодиодных светильников lp 02 40>>>

Фирма Ledos специализируется на производстве и поставке светодиодных светильников в городе Москва. У нас Вы можете приобрести внутреннее и уличное освещение, источники света, а также комплектующие для светильников и прочее. Услуги, которые предлагает компания: подсветка фасадов зданий и сооружений, освещение офисных помещений и прочие виды услуг. Предоставляем скидки своим клиентам. Подробности на сайте Ledos.Su.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated
    • By Tony P
      Twice my hisun has been driven a few miles and turned off back at home. Get back on it same afternoon and console is dead, no lights. 
      Have 12.7 vdc at battery and fuses are good. I hear relays click in the fuse box and main relay clicks but everything is dead. 
      Any ideas on what this may be? I've seen this problem before on this forum but it never finished. 
      Any help is always appreciated. Thanks in advance! 
       
×
×
  • Create New...