Quantcast
Jump to content


Forum Moderators Wanted

Alex

By Alex
in UTV BOARD Announcements

 Share

Recommended Posts

Alex

Alex

Posted
Posted

Are you a moderator on another forum? Interested in becoming a moderator? Do you love UTVs? We are extending an invitation to members who are interested in becoming moderators here on UTVBOARD.

Requirements:

1. Stay active weekly in the forum

2. Move topics started into correct forums if incorrectly placed

3. Change topic titles as needed to make them more relevant for searches

4. Help fellow members with forum posting and adhere to guidelines

5. Help the general flow of the forum and reply to topics that are not moving

Anyone interested, please PM or reply to this topic.

  • Alex unpinned this topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Clayton Walker
      Im New here but just got my Uforce Fitted for Hunting Season
      By Clayton Walker
    • Hutch
      2014 Bennche Bighorn 700 Won't stay running
      By Hutch
      Okay everyone, need some help here. I got my 2014 Bennche Bighorn 700 from my father inlaw. He has had it since new and as far as I know never had any problems with it until recently. It began with it being hard to start and having to give it some throttle for it to start up. Then it wouldn't stay running once it did start. If you go to start it, it will fire right off and only run for a split second and then die. If you give it some throttle it will start and stay running as long as your foot is on the pedal. While it's running its pretty rough and backfires. Here is a list of everything I've done so far. Initially I checked compression and it was low. I changed the cylinder, piston and rings. Took the head apart cleaned and laped the valves. Checked timing a few times. Adjusted the valves. New spark plug. Checked the air filter, it was fine. New battery. Changed the fuel pump because of a broken fitting. Changed the fuel filter, lines and fuel injector. Dumped the old fuel and put new in. Changed the air idle control, TPS, MAP sensor, Voltage Regulator, ECU and harness. I was getting codes 31, 107, 113 and 122 on the display. Once I changed the ECU no more codes have been displayed but still have the same issues. All fuses look good and as far as I can tell Grounds are good unless there are some I can't find. I'm at a loss here. Not really sure where to go. Compression was better after everything I did but I don't remember the numbers. I'll have to check it again if someone thinks that could be the issue. Any help would be greatly appreciated!
    • donny
      New here in NC
      By donny
      Hey everyone new to forum I have a 2014 Odes raider and a 2009 Suzuki Ozark 250 both down atm 😔
    • Alien10
      New here, thanks for letting me join.
      By Alien10
      I have a Coleman Outfitter 550 purchased in January 2022 that runs and operates pretty well.  65 hours on it so far.   It is a work vehicle for my 10 hilly acres with two 1 acre woods and 5 acres of "lawn".  The rest is under a lake. 
      My parking brake does not seem to have any grip.  It worked when new but after a month or so, it is just almost useless.     I press the parking brake pedal hard until it stops. Still, it won't hold even on slight inclines.   I don't see the caliper move as I press the brake pedal down.  There seems to be plenty of pad left on it and the rotor is shiny as if it is rubbing a little when applied, but not enough to stop it from rolling. 
      Any thoughts on possible causes? 
       
    • sister sweety
      New member here
      By sister sweety
      Thank you for adding me, I am the owner of a 2021 axis 700 UTV and also a 2023 Can-Am defender UTV

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...