Quantcast
Jump to content


Recommended Posts

Posted

I just wanted to show you guys my finished electric power steering cost me about $150 to complete and maybe like 12 hrs counting time expend at junk yard,( to pick up a 03 saturn ion e. Steering column and spare linkages )... saw that a guy was selling this kit for about $500 on craigsl.. I went on line and researched a bit so decided to make my own. Not sure if any one has done it not too complicated just time consuming..you will need the 03 ion electric motor, and need to get on ebay and buy this module that a guy sells for about $70, (((module comes with a adjustment knob to set desired torque))helps if you got a welder and some spare steel angle to mount assembly..i will attach some pics ..... haven't been able to take it out but its very easy to turn now..,

post-1941-0-39000300-1426908968_thumb.jpg

post-1941-0-22685400-1426909322_thumb.jpg

post-1941-0-78836200-1426909350_thumb.jpg

post-1941-0-79617700-1426909391_thumb.jpg

Posted

Definitely a nice upgrade. I did mine with a foreign car steering. The guy that sold you the kit made them first for a Corsa B from the UK.. mine works good. Watch high speed with the power cranked up... you definitely could roll it with this kit. Specially with no sway bar.mine is crazy loose at 40mph. Mine will kick out if I abuse it climbing hills locked in all 4's. But my buggy lives on the Rev limiter..!

  • Like 1
Posted

After alot of hard steering the computer shuts itself off so it don't burn up the motor.it usually just takes a few min for it to re-engage. I'm guessing because I run full power all the time.. definitely needed when all 4 locked.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
×
×
  • Create New...