Quantcast
Jump to content


Recommended Posts

Posted

KAWASAKI TERYXâ„¢ 750 FI 4×4 RECEIVES

SIGNIFICANT UPGRADES FOR 2009

Digital Fuel Injection, Digital Gauges and Tilt Bed Highlight Changes

For specific details on each model please click the image above

2009 Kawasaki Teryxâ„¢ 750 FI 4×4

A wide body chassis, big V-twin power and an efficient CVT hallmark Kawasaki’s impressive line of Teryx™ recreation utility vehicles. [...]

View the full article

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
    • By TjB
      My dad has recently acquired a 2510 Kawasaki mule Diesel powered. It worked fine  few weeks and then quit driving. Put a new belt on just to see. Still not driving. It already had a new clutch. Belt turns when in drive or reverse and back wheels are off ground to test. But wheels not turning. Thoughts? 
    • By rsar
      So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price.  Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone  windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for.  Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.




×
×
  • Create New...