Quantcast
Jump to content


Hi/Lo Cable Failure and Repair

mncasto

By mncasto
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

mncasto Newbie

mncasto

Posted
Posted

I can no longer shift my 2011 4010 into Hi range. Using the shifter. I can manually pull the shift lever into high range and then the shifter can be used to push it back into low range. If the cable is a fixed length end to end and it's attached on both ends then there must be some magic going on somewhere. Does anyone know how this cable is constructed. Is it possible something is disconnected or broken in such a way that the cable can push but not pull?

  • 1 month later...
dcg9981 Newbie

dcg9981

Posted
Posted

There should be an adjustment at the bracket on the transmission side. I am currently having a similar issue, mine still goes into high gear nut you have to slap it in or when you touch the throttle it grinds, I believe this is linkage issue, I am going to try adjusting it out and see what happens.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
    • Bryan g
      Coleman UT400 shift issues , grinding .
      By Bryan g
      We see a lot of the UT400 with shift problems, not going into gear, popping out of gear, grinding etc. There  is a bulletin Im sure everyone has saw about adjusting shift cable.  That dont always fix it.  I went round n round with coleman  on couple units. We are a Coleman warranty repair center"AFS Small Engine Repair "   I told them shift lever does not have enough travel .  No amount of cable adjustment  will increase travel . I  extended lever with piece on flat  iron by 3/4 of inch .  This gave shifter enough travel to properly engage into gear completely .  Last couple units to come in for this Coleman sent me a modified shift lever, with longer travel . Problem solved! Also , heads up if you get any new unit ,,,go over and check it out,  grease  all zerks, check air filter for being in backwards, check wiring harnesses for rubbing on rotating parts,  brake hose  routing , make sure not touching exhaust .  These are just  few of the more common failures I see .
    • Bloodhound
      2016 can am commander
      By Bloodhound
      Don't know the size anyone know the reliability fo theae
    • Jim Kessell
      EH65 spitting fuel from breather hose into air filter.
      By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...