Quantcast
Jump to content


Hrs. on a UTV

ronmat

By ronmat
in UTV General Discussion

 Share

Recommended Posts

ronmat Newbie

ronmat

Posted
Posted

Im looking at buying a 2009 4010 Trans Mule it has 1300 hrs, looks clean and taken care of, but this is my first

UTV purchase and was wondering is this too many hrs? They are asking $7500. What do you people thing with

much more knowledge than i on this UTV.

Thanks

Ronnie

studebaker53 Rookie

studebaker53

Posted
Posted

Both of my units 3010 and 4010 hour meter seem to run fast. Although yours shows 1300 hours in reality its probably only 900. Biggest thing to check is that it doesn't burn oil and motor noise..i.e. knock. Check motor compression before buying. Otherwise your good to go. One big problem those units have are the primary and secondary clutch wearing out. If the transmission grinds when going into gear.....most likely the primary or secondary clutch needs to be worked on or replaced.

  • 5 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rsar
      Washing Mule Underbody
      By rsar
      Hey guys. I was wondering if anyone pressure washes their Mule underbody. Three years in, I have yet to do this. I'm worried that the pressure washer could damage or dislodge something but it's gotten to the point that it could use a bath. Any thoughts?
    • Steve Waldner
      Looking for a Kioti Mechron 2200
      By Steve Waldner
      Looking to buy a Kioti Mechron 2200
    • TjB
      2510 Kawasaki mule Diesel
      By TjB
      My dad has recently acquired a 2510 Kawasaki mule Diesel powered. It worked fine  few weeks and then quit driving. Put a new belt on just to see. Still not driving. It already had a new clutch. Belt turns when in drive or reverse and back wheels are off ground to test. But wheels not turning. Thoughts? 
    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
    • rsar
      Kawasaki Mule Cab Eclosure
      By rsar
      So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price.  Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone  windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for.  Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.




UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...