Quantcast
Jump to content


Trooper T4 No Spark

Countryboy59

By Countryboy59
in Joyner UTV SxS Forum

 Share

Recommended Posts

Countryboy59 Rookie

Countryboy59

Posted
Posted

Does the Trooper T4 need to have the fuel pump running and build pressure before the Ign. has spark?

I bought a used T4 that ran when it was setup 4 years ago. Drained gas tank.

Checked for spark at plug wire, None! Did not hear fuel pump run when cranking.

Does it have spark even without fuel pump in operation. I checked all the fuses they are OK.

I do have the manual.

post-3653-0-18906700-1463533842_thumb.jpg

  • 1 year later...
Dan B Community Regular

Dan B

Posted
Posted

I have an R2-1100cc witch is almost like a trooper with a different body style. After I turn the ignition on, I have to wait about 3-5 seconds for the gauges to cycle before I can start the engine.  It probably has something to do with the ECU "booting" up.  I don't think the ECU gets power until the ignition switch is in the "ON" position.  Like the computer you are using now, you can't turn it on and use it until it boots up.  At least that'w what makes sense to me.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Matthew Smith
      SXS No Crank at the Key and No Spark
      By Matthew Smith
      2013 Bennche Bighorn 700 EFI
       I just picked up this project that I was told would crank, but not start.  This is what I’ve figured out so far….
      I installed a new battery and get all dash lights, head lights, and brake lights on when turning the ignition on.  Fuel pump even turns on.  It does not crank with the key, but would when I jumped the starter solenoid, so I replaced it…..no change.
      Figured I’d check for spark and compression while I was dorking around.  Compression is 150 psi, but there is no spark.  Replaced the spark plug… no change.
      So, is my new starter solenoid bad?  Could it be the brake or gear position switches even though the brakes and neutral lights come on?  Not sure where to go from here.




    • SteveS
      2021 Massimo MSU 800 will not run above 20 MPH
      By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       
    • Jim Kessell
      Predator 670 manual oil pressure gauge
      By Jim Kessell
      Hi All
      Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?
      Thanks in advance for your advice !!
      Jim
    • downseast
      2020 T-Boss 410 running problems
      By downseast
      Hi everyone
      Recently purchased a 2020 T-Boss 410 in what appears to be good condition
      First time with this machine – I also have a diesel Kawasaki Mule which so far seems a better machine
      It didn’t start and idle well particularly from cold when I got it and sudden take off ( now solved with new clutch parts ) was all or nothing !
      I have replaced the idle valve, throttle position sensor, had the injector professionally checked ( ok) and also the pressure sensor this is a fuel injection engine, also plug and lead etc!
      It still doesn’t run well and when starting I have to hold revs for a while as it wont idle but stall, thereafter its better and I have rebooted the ecu which has improved it
      When I go to start it clicks as if there is a hydraulic lock and wont return after two or three attempts it then does turn over and start bit I need to give it a bit of throttle to start – is this normal ?
      Is there adjustment for the air idle valve ?
      The engine seems rough and with vibration compared to other engines I have been used to but some say this is normal?
      I haven’t changed the Lambda sensor yet, anyone know how much difference this might make ( I have a new Bosch universal to fit )
      Any advice very much appreciated, thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...