Quantcast
Jump to content


2014 R2 Wiper Kit

dnastauf

By dnastauf
in Joyner UTV SxS Forum

 Share

Recommended Posts

dnastauf Rookie

dnastauf

Posted
Posted

Anyone ever try buy a wiper kit for a newer Renegade? Well I did and what a hassle it was until I contacted Borossi Motors LTD in Europe. First I contacted Joyner USA and they flat out told me Joyner doesn't make one. After I found a part number for one for a 2008 R2 800 (I didn't think there could be too much of a difference), I contacted Silverbullit. There I was told we don't use part numbers and basically Joyner doesn't make a wiper kit. So check Borossi Motors and guess what, they actually had one advertized in their parts and accessories. It even had the same part number I gave silverbullit. So I thought I'd give them another chance. This time I got they have to, they use them like cars, I've been in business for 15 years and might of had two calls for wipers, it must be aftermarket, and last but not least Borossi is a good dealer you might as well buy it from them. Well I did, it cost me $155 USD, came in two weeks and plugs right in. The only thing I'm changing is going to silicone wiper blade, don't have a glass windshield.

NO WONDER TEAM JOYNER USA WENT UNDER

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • rdborra
      Bobcat 2200 dump bed relay pops fuse and stalls after warm
      By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • CYJSP2009
      2022 brandnew Joyner CV Axles and CV Joint rebuild kits are comming
      By CYJSP2009
      Dear Friends, 
      2022 Brand new Joyner CV Axles and CV  Joint rebuild kits are comming 
      1.  S650.03.02.02.00 ---Joyner 650 Commando Rear
      2. TR1100.03.01.03.00 --- Joyner Trooper Front 
      3. TR1100.03.02.03.00 --- Joyner Trooper Rear
      4. D650.03.02.02.00 --- Joyner 650 Sand Spider Rear Left 
      5. D650.03.02.03.00--- Joyner 650 Sand Spider Rear Right 
      6. SV800.03.02.01.00 --- Joyner 800 Viper, SV1100 Drive shaft Left
      7.  14274 --- 650 ider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      8. 15803  ---  650 Sand Spider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      Attached are the part photos for reference. 
      Above parts are now on the way to USA, will be ready for inland delivery in middle of July. 
      Price: CV Axle: USD250/ Piece;  CV Joint kit （without grease): USD110  send to door. 
      There will be special discount availabe for deals completed within July 2022.  
      Buy 1 piece: Get 5% discount, 
      Buy 2 pieces: get 10% discount.
      Buy 3 pieces: get 15% discount, 
      Buy 4 and more than 4 pieces: get 20% discount. 
      Please kindly note Qty for each part is not big  and it is hard to forcast when there will be next offer for these kind of products unless there is sufficient confirmed order qty for productioin arrangement. 
      Payment method: Payoneer payment link ( can pay through bank account or credit card) or Paypal ( [email protected]) .  Payment commission paid by the buyer. 
      Interested parties, please contact [email protected]. 
      Thanks
      Good Luck
      Casey / Leaf Asia
      July-07-2022
       
       
       














    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...