Quantcast
Jump to content


Trooper Tie Rod ends

silverbullet

By silverbullet
in Joyner UTV SxS Forum

 Share

Recommended Posts

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet

We have solved the tie rod problem. We use a heim joint chromoly and spacer.It comes with a seal and a plated bolt.This will last for years.Do not put a zerk fitting in heim.That only increases dirt getting in

Thanks Rich

  • 2 years later...
  • 3 months later...
Volkz VLOGS Contributor

Volkz VLOGS

Posted
Posted

Yeah.. Not cool at all!  I had bought from him several times.. Then he took me for $200 and some odd dollars.. could be worse I guess.. I heard he had/owed people engines!

  • Sad 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Texjpr
      Help! Hub safety-hour meter switch problem
      By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • mac66
      Anyone have a Bad Boy Bandit?
      By mac66
      Apparently, these are Hisun or at least they use Hisun engines. I can't find much info on them online yet.  Ran across a used one with just 100 miles on it as a very reasonable price.  Just curious.
      Okay, more info...they are owned by Textron Corp who also owns Bell Helicopter, Cessna & Beechcraft aircraft, Ez-Go & Cushman and Arctic Cat and a bunch of other companies.
      So are thy cheap Chinese crap machines or are they good to go?
    • sxr951
      anyone ever have to beat your starter out with a hammer till it broke in half?.lol
      By sxr951
      corrosion had its oring neck area  jammed in.. and besides that had corrosion in the starter just shorted when ran direct jumper cable to the starter post power to it

    • Jason S
      2022 Bobcat 34XL Brake pedal depress to start getting impossible
      By Jason S
      Good afternoon,
      I have a 2022 Bobcat 34XL.  Over time, I have to press harder and harder on the brake pedal before the ignition will fire. Now I have to practically stand on it with all my weight to get it to start.  Does anyone know if there is a spring or something that might need replacing, or have had this issue before? I don't have any schematics of the brake sensor/assembly.
      TIA

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...