Quantcast
Jump to content


Supercharger

silverbullet

By silverbullet
in Joyner UTV SxS Forum

 Share

Recommended Posts

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet

This is the most advanced Supercharger for Chery Engines.This is a modulator system for all Chery Engines.

We are going to dyno it in a few weeks.This is the third one we have made changers to.They all worked well but want to build the best performing one.Each one has inproved torque on the low end.Different runners and shape of the manifolds.Coming soon no turbo lag.Just touch the pedal and you are gone.Inter cooler is built in.

Any questions just send your question to my email.928 344 2117 [email protected]

This system will fit Joyner,Renli,Sand Reeper and any other Chery based power train.

Thanks Rich

post-339-0-73048600-1479584992_thumb.jpg

post-339-0-45299700-1479585080_thumb.jpg

  • Like 1
Link to comment
Share on other sites
silverbullet Experienced

silverbullet

Posted
  • Author
Posted

Silverbullet

I have seen turbo charger kits on the websites.I see pipes hoses exhaust system.But never have seen a dyno sheet.I mean never over all the years we have built performance parts.I tried to build one and it was just two twitchy.Turbo lag is just the most aggravating thing that i decided never to build one to sell.Our supercharger has none of these problems.The all you get is instant power from start to finish.We have them for all Joyner's,Models including Renli,Sand Reeper and any other buggy that uses the Chery engines.

Link to comment
Share on other sites
  • 2 months later...
silverbullet Experienced

silverbullet

Posted
  • Author
Posted
3 hours ago, dwaynebradley377 said:

Believe it's actually a fuel problem I can get to run great at full throttle just rich at accel,I am using o2 wide band to monitor ratios.
Should have bought turbo kit from a reputable dealer think is my problem

Sent from my SM-G920W8 using Tapatalk
 

Silverbullet

Hi

Did you have a problem from the beginning or is it something that just happen.Let me know did you install the kit or was it installed buy some one else what is the fuel pressure your running an did you put bigger injectors.

Rich

  • Like 1
Link to comment
Share on other sites
dwaynebradley377 Enthusiast

dwaynebradley377

Posted
Posted

I bought xy groundpounder new and same with klung turbokit 

Came with an emanage blue ecu that never worked and of course no warranty. 

Ended up getting Dobeck to make me a EJK module  with custom tune,using a diode to bleed off extra voltage on map sensor so won't see boost and bypassing factory o2 sensor with a simulator . Kept factory injectors 

It does haul ass now  but runs rich when first start to accel for a second or 2 ,

Verified with my wide band 

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 months later...
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Fishing Wiskers
      2012 Axis 500 4x4, no power going up hill
      By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
    • Woody77
      Stator replacement an now want start
      By Woody77
      UTV MASSIMOREPLACED STATOR WANT start replaced rectifier still want start stator ohms out 5 ohms each leg what could be wrong at this point 
    • Paul Angstadt
      Hi y'all. New to this stuff. in Florida.
      By Paul Angstadt
      Hi everybody. I just bought a 2012 Hisun with the 700cc engine. Was wondering where i could find a service manual for this thing?
      Its going to need some parts that are missing, like the air intake hoses and other things. Also the dash display is out. the only light that works is neutral light. Not even sure on the model. from pics I've seen, it looks like an HS700. Kind of grey with the black stripes on the hood. Just hoping i can find parts for it.
      Thank you for any advice you can give me. By the way, it does run and goes forward and reverse.
      Paul
    • diamondjfarm
      Good mornin' all. Just joined.
      By diamondjfarm
      I got an old 2003 Arctic Cat 375 Auto, and just bought a 2008 AC 650 side by side. Got a new starter, solenoid, and battery for the 650. Gonna change the crankcase oil and filter while I'm at it.
      Anything I oughta watch out for from them that's done the starter/solenoid on this model?
      Don't have a manual yet for the 650. Any recommendations for oil weight/grade?
      Thanks.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...