Quantcast
Jump to content


Recommended Posts

Posted

my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated

Posted

go back to the basics. check compression, check spark, remove injector and crank to see if fuel sprays. Sprays!, not drips or squirts like an old man.

I already suspect a plugged up injector. If so, you can try to clean it up, but they're not expensive. I would recommend also adding an inline filter.

Good luck. Keep us posted

Pop Bob

  • Like 1
Posted

Man, I agree with Pop Bob that it is likely the injector.  Some Hisuns were manufactured and sold without an in line fuel filter.  There have been several videos on line of folks suffering from the resulting clogged or malfunctioning injectors.   They simply do not like anything in the fuel they are spraying.    Adding an in line fuel filter is easy, and an absolute must. 

Posted

i do have a new inline filter. and tried a new injector. i have ordered a more expensive injector to try that. Will let you know what happens when i get it.

Posted

nope tried a more expensive injector and still wont start guess i will finally have to take it into a shop. Ran out of ideas. 

  • 1 month later...
Posted

i dont know i was driving and it started losing power so i shut it off. then 10 min later started it went about 500 feet down road then it just died. the motor made no weird noises or anything like backfiring or clanking. The mechanic said it hit the valves.he said he tried resetting timing chain and while cranking it it jumped again.so waiting for parts to come in and get rebuilt at shop. the machine only has 300 hours on it.sucks i only put 30 miles on it after I bought it used

Posted

Unless you know the former owner, there is no telling what kind of life it had in its 300 hours.   Maybe you have already gone over the machine but check for signs of rough use. Do zerks and joints appear to have been maintained, brake pads, hidden areas packed with mud?  I know its a UTV but there may be signs of it being "abused" as opposed to just being "used".

Sorry you are having such issues.  

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Homeowner A
      Is there a better performing higher volume injector than what they come with or what is the best replacement for the original?  
    • By vachi
      hi everyone i have this 2021 Hisun forge 250 that won't start. no spark no fuel.   when i turn the key on i dont hear the relays click or fuel pump come on. it does have power but the relay doesnt ground the pump or the ignition coil. dont know if there are any safety switches on this model or not.  it does crank and all the accessories work. i  hot wired the pump and it does work.  i found a wiring diagram but it's very hard to figure out and was hoping someone has seen this before. all fuses are good. thanks in advance. 
    • By Robby
      Hello, I have a 2013 500 utv hisun. Was running ok and cut out while parked. Bike will not start now. It turns over, but won't fire. I have no spark and no fuel. I replaced fuel pump, ignition coil, spark plug, cdi, voltage rectifier and all the fuses and relays. Could bad stater cause no fuel because I can't hear the fuel pump priming. Any info on where to start looking for problem.
    • By Ductking1
      I recently purchased a 2024 Hisun 550 Sector from Kreps Service Station and am having issues with the gear selector, I am doing as instructed in the owners manual but the shifter acts like it is binding or the button lock isn't releasing, the shifter will not move, I have to wiggle it back and forth while pushing hard on the brake and if it's in park or reverse it's nearly impossible to get it to move, I contacted Justin Krep and he says this is normal with these machines, I find that hard to believe, I've owned many utvs and side x sides and have never had this kind of issue with any of them, any help with this problem would be greatly appreciated.
×
×
  • Create New...