Quantcast
Jump to content


Joyner trooper with with Suzuki samurai axels..????

Tobie1987

By Tobie1987
in Joyner UTV SxS Forum

 Share

Recommended Posts

Tobie1987 Enthusiast

Tobie1987

Posted
Posted

I seen a razor 800 with Suzuki samurai axels and transfer case..it got me thinking about doing it my trooper..there cheap and a great 4 link setup.. may even rear hydro steering too.. just a thought... wondering what you all thought about it..???

 

 

Sent from my iPhone using Tapatalk

  • Travis featured this topic
2scoops Proficient

2scoops

Posted
Posted

Lol, of course I have.  That's why I have a suzuki samurai parts car sitting in my yard.  I was planning on starting with a transfer case install. I am also thinking about a rear axle install only with front ifs, but matching gearing will be tough.  If you go full solid axle you WILL miss the ride of the independent suspension. 

  • 4 weeks later...
Tobie1987 Enthusiast

Tobie1987

Posted
  • Author
Posted
Lol, of course I have.  That's why I have a suzuki samurai parts car sitting in my yard.  I was planning on starting with a transfer case install. I am also thinking about a rear axle install only with front ifs, but matching gearing will be tough.  If you go full solid axle you WILL miss the ride of the independent suspension. 





Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • SteveS
      2021 Massimo MSU 800 will not run above 20 MPH
      By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • Tejun
      Coleman 550 Rear Differential Leak
      By Tejun
      Neighbor rode their Coleman with the park brake apparently not fully released. Needless to say, things got pretty hot and even started smoking and the smoke was definitely gear oil smell. Looks like oil is coming from the area just behind the disc for the park break. Looking at parts diagram, there is an oring behind the nut/washer that attaches the flange to pinion shaft. I'm not finding anything on YT that would help with disassembly. Anyone have some experience with removing rear driveshaft ?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...