Quantcast
Jump to content


Recommended Posts

Posted

My new 2017 Polaris Ranger has tires going low. When I went to check pressures in all tires one cap was on tight and I noticed the valve stem rotated easily. I checked all 4 and  all stems spun with ease. Either the holes for the stems are too large or the stems are too small.
i'll get new stems and go from there.

Anyone else have the same problem?

Posted

In my Kawasaki Mule 550, my front left tire kept going flat, and the wheel wasn't properly "Seated" you might say around the tire it self, put stop a (1) can of stop leak, works perfectly now!

Posted

used soapy water but no bubbles at valve or rim, slow leaks are annoying. Could just be that 10 psi is not enough to keep them air tight.

Posted

I'd rather find the cause of the leak. Stop leak can throw a tire off balance to make it a problem  (on road driving) It goes 50 mph !

I could invest in a small electric compressor for the trail.

Posted

not at all, I didn't know they existed. The one that connects to your battery looks like a good one. I should get a tire patch kit too. Nothing like walking out miles from the trails just to walk back with repair items. A spare tire would be good but pricey.

Posted

we get ripped off here in Canada. Everything extra and add 30% more since our $$ sucks. First the bank of Canada lowered the $ and then the economy so the govt blamed it all on the economy and not what they did, go figure?  All our small products at grocery stores shrink and prices rise. I love going to Watertown and seeing real normal sized cans etc.

Posted

Hillary is one of many who was corrupted by Saudi $$$$$.   Trudeau has taken much from them by just looking at his immigration policies.

Posted

Yes most of us up north want this. Every time they vote in Liberal it only means higher taxation and free room and board for economic refugees.

We all work for the govt. here with ultimately 60% of our wages grabbed back as tax. I wish I was living in a state without income tax and near a bordering state without sales tax

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jerrys500
      Hi I'm about to order parts to do a bunch of work on my Massimo. Does anyone know if there's a difference in the top end kit {piston, Cylinder, Rings, Gaskets, Piston Pin} if it has a carb or EFI? I'm EFI and I think some came with a carb so I thought i'd ask before making a mistake...
      Thanks Jerr
    • By Homeowner A
      Picked up an essentially new 2022 UT400 with 9 miles on it.  Decided to change the oil because it's probably never been done.  Pulled the dipstick and noticed it was overfull then went and pulled the drain plug and took off the filter and it was like brown water running out.  What should I start checking?
    • By Duncan
      I got a utv from lowes it has one tire in the back that is the same size as the front tires so it has 3, 26-9-14 and 1 26-11-24. i want to change the rear tire to the same one as the other.So instead of buying a new rim will a 26-11-24 tire fit on a 26-9-14 rim.
    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

×
×
  • Create New...