Quantcast
Jump to content


2006 Joyner 800cc FI owner

mightymikee

By mightymikee
in New Members Area

 Share

Recommended Posts

mightymikee Newbie

mightymikee

Posted
Posted

Hi guys,

I wanted to drop by and say hi. 

Just picked up 2006 Sandviper 800cc FI with fox air shocks. 

Want to do a full tune up and looking to gain some knowledge from the wise around here. 

So here is my buggy. 

Hello yall!

 

IMG_20170524_212157.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • FTG-05
      Want a new work UTV; who and what should I look for?
      By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • Steve Waldner
      Looking for a Kioti Mechron 2200
      By Steve Waldner
      Looking to buy a Kioti Mechron 2200
    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • Bloodhound
      Looking to purchase
      By Bloodhound
      Any info on the duribility and reliability of these  don't know the size
      And also 2006 rzr duribility and reliability 800cc
    • CRV
      Hello .. I have a 2007 cub cadet big country
      By CRV
      I’m need a couple parts. Diff. Lock Actuator mainly. But I would like to find a donor that maybe has bad motor or something along those lines. 
      if anyone has or knows of anything please holler at me 
      thanks Randy 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...