Quantcast
Jump to content


Recommended Posts

Posted

I'm curious if it is possible to put a snorkel on my trooper that is also turboed or is there any problem areas that come up when getting wet like electrical parts. Just a random thought.

 

 

Sent from my iPhone using Tapatalk

Posted

No problem at all but make sure every hose on the engine have a clamp on it (vaccum,pcv valve,also make sure the hole where the generator coil wire come out whit the crank sensor wire are siliconed. You will notice probally a 5% engine performance lost due to the snorkel (same story for a car engine snorkeled) but its not a big deal 

Posted

silverbullet

You can get top performance.Use 2" 3" adapter  2 " side from hose than run 3" PVC to roll cage 90 degree up to top.Hose clamps for roll cage than K&N for trail riding.Uni filter if you run in sand.PVC pipe cut and Glue it.Its very important to do.We rebuild 40 to 50 engines every year from all over the county.We build stock engines and Performance parts.We are experts on Chery engines.And yes we build the 2 cylinder engines.We can get you 85 MPH +

Rich

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Nutcase
      I have a Joyner Trooper 1100 4 place that has been sitting for a number of years. I have everything taken care of but i can't get the fuel through the injectors. Fuel pump puts full pressure on them but they don't turn on or spray fuel. Any ideas?
    • By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By JimWil
      Looking for a place/website to order a  replacement bench seat and a dump bed fender from.
      Pics are the original orange when purchased and after painting with a textured bed liner type coating.
      Just looking for those two parts as mentioned above.
      JimWil
×
×
  • Create New...