Quantcast
Jump to content


2005 Joyner Sand Spider

rgilstrap

By rgilstrap
in Joyner UTV SxS Forum

 Share

Recommended Posts

rgilstrap Rookie

rgilstrap

Posted
Posted

Hello all, im new to the board and the utv world. i bought the Joyner a few weeks ago. cost me $600. has Garrett turbo not sure what model. the problems i am having and could use some help on are as follows. a my carb needs to be rebuilt. i can not find a place to just get the gaskets and needles from. any ideas. i am only getting about 90 psi on both cylinders. its a little low. and my fuel pump and regulator. just a mess. i am having trouble finding places to just buy rebuild kits. is there such a place?

silverbullet Experienced

silverbullet

Posted
Posted

silverbullet

The compression is way to low 90 psi will not work.Rebuild the engine and then see what else you need.But first rebuild it parts are no expensive.We carry all engine parts.Plus i know a lot about Joyner Engines.We rebuild 40 to 50 engines a year.All models of Joyners from all over the country.

Thanks Rich

928 344 2117

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Paul L
      Kubota RTV-XG850 Sidekick shifting into nuetral problems
      By Paul L
      When I am driving at 30 to 40 mph on the highway, the display will change from H (high) to R (reverse).  It does not actually shift into reverse, it seems to shift into neutral and starts losing speed and the gas pedal has no effect.  After the rpm/speed drops for 5 seconds or so, it changes back to H and runs fine for another minute or so.  You have to try to drive it at less than 5000 rpm or so, to try and keep this from happening.  Any ideas on what the problem might be?  It only happens at the higher speeds.
    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • CSM_Retired
      Kioti UTV SxS Forum
      By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...