Quantcast
Jump to content


dump bed problems

marypippin14

By marypippin14
in UTV General Discussion

 Share

Recommended Posts

Travis Grand Master

Travis

Posted
Posted

Welcome to the forum!

First off, did you buy the lift for the bed, or did it come with it?

More than likely a clicking noise, usually means a solenoid has gone bad and is not engaging properly. But i am not very familiar with the dump bed lift, and how it is set up. I will try to find some more information  quickly.

 

 

  • Like 1
Link to comment
Share on other sites
kenfain Experienced

kenfain

Posted
Posted

This sounds like an aftermarket lift. The factory lift is hydraulic IIRC. If it is electric, then it probably has a worm screw driven mechanism. If this is an aftermarket lift, try giving it a helping hand by pulling up on it while operating the lift switch. You might need some help with the lifting up of the bed. Sometimes the worm screw just needs some help getting to some good threads. Of course the bed should be empty when you do this. If this is the problem, you'll be able to hear it turning. And if that's the case, and this fix doesn't work, you'll have to pull the bed hinge pins, raise the lift, and replace the pins. Do this while it's raised.

   If this works, then you'll always want to keep the bed up about a half inch from the bed rails. That way it'll always be in the good threads. The fix gets easier after you've done it a couple of times. Hope this makes sense.

  • Like 2
Link to comment
Share on other sites
marypippin14 Rookie

marypippin14

Posted
  • Author
Posted
On ‎2‎/‎16‎/‎2018 at 6:54 PM, kenfain said:

This sounds like an aftermarket lift. The factory lift is hydraulic IIRC. If it is electric, then it probably has a worm screw driven mechanism. If this is an aftermarket lift, try giving it a helping hand by pulling up on it while operating the lift switch. You might need some help with the lifting up of the bed. Sometimes the worm screw just needs some help getting to some good threads. Of course the bed should be empty when you do this. If this is the problem, you'll be able to hear it turning. And if that's the case, and this fix doesn't work, you'll have to pull the bed hinge pins, raise the lift, and replace the pins. Do this while it's raised.

   If this works, then you'll always want to keep the bed up about a half inch from the bed rails. That way it'll always be in the good threads. The fix gets easier after you've done it a couple of times. Hope this makes sense.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • NHTracker
      Cracks in my bed
      By NHTracker
      I have a 2020 Tracker 800SX LE that I bought new in 2020.  Yesterday I noticed two cracks in the bed on the inside corners at the tailgate end.  They go all the way through.   I use it around the property moving firewood, dirt and stuff.  Never put stress on the sides of the bed.  Has anyone else had this problem?  Is there a fix?  Help!!!


    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • diamondjfarm
      Good mornin' all. Just joined.
      By diamondjfarm
      I got an old 2003 Arctic Cat 375 Auto, and just bought a 2008 AC 650 side by side. Got a new starter, solenoid, and battery for the 650. Gonna change the crankcase oil and filter while I'm at it.
      Anything I oughta watch out for from them that's done the starter/solenoid on this model?
      Don't have a manual yet for the 650. Any recommendations for oil weight/grade?
      Thanks.
    • mac66
      Anyone have a Bad Boy Bandit?
      By mac66
      Apparently, these are Hisun or at least they use Hisun engines. I can't find much info on them online yet.  Ran across a used one with just 100 miles on it as a very reasonable price.  Just curious.
      Okay, more info...they are owned by Textron Corp who also owns Bell Helicopter, Cessna & Beechcraft aircraft, Ez-Go & Cushman and Arctic Cat and a bunch of other companies.
      So are thy cheap Chinese crap machines or are they good to go?
    • FGT
      How to wire a C/B into a dual battery set up
      By FGT
      QUESTION: How to wire the C/B into this current dual battery set up.

      EXISTING SITUATION: MAIN Battery is OEM and feeds OEM circuits. Added an AUX Battery in the OEM dual battery location. Connected the AUX - terminal to the MAIN - terminal. Connected the 100A Accessory Fuse Block power cable to the AUX + terminal. Installed a smart isolator between AUX and MAIN batteries where a cable from AUX + goes to the isolator and a cable from isolator to MAIN battery + terminal. Installed separate QD battery tender cables to both AUX and MAIN batteries + and -. The dual battery system appears to work as intended. For this Phase 1 improvement, to avoid having to constantly pull the leads on the AUX + battery post off and put on, for testing or maintenance of Accessory circuits, I wanted a more convenient and safer way to open the circuit from the AUX battery + terminal the Accessory Fuse Block. I called an off road dealership and was told to install a much larger capacity circuit breaker than the 100A rated Fuse Block and was recommended to get a 250A C/B like the one in the pic, which I did. I was told the reason for the C/B high amp rating was two-fold (a) to trip in the event of a battery short circuit and (b) to be able to conveniently open the C/B to kill power to the Accessory Fuse Block without removing leads from the AUX + terminal. The 250A C/B has two posts labelled "BAT LOAD" and "BAT LINE". There are currently three connections to the AUX + post: (1) Accessory Fuse Block power cable, (2) cable to Isolator AUX in terminal, (3) cable from AUX battery charger.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...