Quantcast
Jump to content


dump bed problems

marypippin14

By marypippin14
in UTV General Discussion

 Share

Recommended Posts

Travis Grand Master

Travis

Posted
Posted

Welcome to the forum!

First off, did you buy the lift for the bed, or did it come with it?

More than likely a clicking noise, usually means a solenoid has gone bad and is not engaging properly. But i am not very familiar with the dump bed lift, and how it is set up. I will try to find some more information  quickly.

 

 

  • Like 1
Link to comment
Share on other sites
kenfain Experienced

kenfain

Posted
Posted

This sounds like an aftermarket lift. The factory lift is hydraulic IIRC. If it is electric, then it probably has a worm screw driven mechanism. If this is an aftermarket lift, try giving it a helping hand by pulling up on it while operating the lift switch. You might need some help with the lifting up of the bed. Sometimes the worm screw just needs some help getting to some good threads. Of course the bed should be empty when you do this. If this is the problem, you'll be able to hear it turning. And if that's the case, and this fix doesn't work, you'll have to pull the bed hinge pins, raise the lift, and replace the pins. Do this while it's raised.

   If this works, then you'll always want to keep the bed up about a half inch from the bed rails. That way it'll always be in the good threads. The fix gets easier after you've done it a couple of times. Hope this makes sense.

  • Like 2
Link to comment
Share on other sites
marypippin14 Rookie

marypippin14

Posted
  • Author
Posted
On ‎2‎/‎16‎/‎2018 at 6:54 PM, kenfain said:

This sounds like an aftermarket lift. The factory lift is hydraulic IIRC. If it is electric, then it probably has a worm screw driven mechanism. If this is an aftermarket lift, try giving it a helping hand by pulling up on it while operating the lift switch. You might need some help with the lifting up of the bed. Sometimes the worm screw just needs some help getting to some good threads. Of course the bed should be empty when you do this. If this is the problem, you'll be able to hear it turning. And if that's the case, and this fix doesn't work, you'll have to pull the bed hinge pins, raise the lift, and replace the pins. Do this while it's raised.

   If this works, then you'll always want to keep the bed up about a half inch from the bed rails. That way it'll always be in the good threads. The fix gets easier after you've done it a couple of times. Hope this makes sense.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • Clayton Walker
      Im New here but just got my Uforce Fitted for Hunting Season
      By Clayton Walker
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Brett
      2006 Polaris Ranger 700 side by side idles fine but dies when you touch the gas
      By Brett
      Fuel injected 700 starts great and idles great but touch the gas and it dies
    • redneckred
      Gremlins in the machine
      By redneckred
      I have a 2012 Bennche Bighorn 700X.  I bought it used.  It had been sitting in a field for several years untouched.  I put a new sun gear in the shifter, new shifter linkage due to the old one having been patched, and a new battery (and of course fresh fuel).  The machine cranked and ran beautifully.  I had it over a year and then the machine quit running.  As it would not stay cranked, I narrowed the problem down to a bad IAC valve.  I replaced it and it ran as good as new/old.  Fast forward, the machine started to act like reverse wasn't catching and would not always back up when in gear.  Then forward quit.  I assumed a bad CVT belt and got one.  Started removing the bolts from the cover and (3) just turn in the housing without coming loose.  (2) are on the bottom, so very little room to do anything with them.  I tried cranking the machine again to see the belt move since I can move the cover enough to see the belt and now the machine will not crank.  It turns over fine.  It gets gas to the injector and has spark.  I can spray cleaner down her throat and she would run until it ran out.  I have replaced the IAC twice and put a new injector with no change.  I went out and put the old injector back in to see if that made any difference and, well, it did.  I tried to crank the machine and the starter is stuck trying to turn the machine over even with the key off.  I have to disconnect the battery to stop it.  Before I shoot this thing, what am I missing?  Is this an ECM problem or something else I am not seeing?  Been dealing with these Gremlins for over a month now and weeds are starting to overtake the motor due to it not moving.  I would love to get the thing running first and any ideas of getting those CVT cover bolts out would be extremely helpful.  Thanks in advance.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...