Quantcast
Jump to content


Recommended Posts

Posted

I live in the desert southwest where temperatures go above 115 a few days a year.  On my next oil change, I'm going to try 10w or 20w-50.  My Renegade oil pressure at idle is barely 10psi (new sending unit).  I prefer 20psi at idle.   I'm hoping that will improve my oil pressure at idle.  Edited:  The 2016 owner's manual for the Renegade (it has the same 1100cc engine as the Trooper) say to use 10W30-50 oil.

  • Alex changed the title to What weight of oil and brand Joyner 1100
  • 3 months later...
Posted

Monty Herbold...Run  Royal Purple 20W-50!!

 And Dan B ......I ride out in Johnson valley Ca, .... I've always ran Royal Purple 20w-50.  First time out on start up had 30-40psi at idle and had 70+psi if I was on it...... But dropped to 10-15psi when just of the trail (Hot) and at idle..(still 70psi if on it)... Needed better cooling!   What you need is a Oil cooler kit + Royal Purple 20w-50!! That's what fixed it for me!!

Posted

Okay!  Thanks for the info.  I'll look at getting an oil cooler.  There was one time I noticed that my idle pressure was about 10 psi.  Then later during the same ride it was near 20 psi.  I'm wondering if a problem is developing in the oil pressure relief (bypass valve) adjustment; maybe sticking slightly open at times.  I'm not familiar enough with the Chery engines but I do know that regular cars have that adjustment in the oil pump.  Older cars had that adjustment in the engine block near the oil filter.

Posted

Mine was similar but, I could attribute the low pressure to oil temperature from the riding I had just been doing (lots of throttle and heavy loads).. I don't have an oil temp gauge but, I just know that the oil was hot LoL!! I'd go with  the cooler and if you got problems still.. I'd say it might be in the oil bypass for you.. If so, it's in the oil pump assembly on a chery engine! But, lets hope not!! LMAO

                                                                   

Capture+_2018-09-15-16-59-32.png

Capture+_2018-09-15-17-01-01.png

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      Hi All
      Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?
      Thanks in advance for your advice !!
      Jim
    • By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks
    • By BMurph
      Hello everyone! I am new here and have no experience with UTVs but I am quickly getting some. I have a shifting problem where I can shift through all gears without the engine running but as soon as I start the engine I can not select a gear. Yes, foot is on the brake and yes the pin is being pulled to go into reverse if I was to try going into reverse. The shift lever does not move. I adjusted the linkage to get more accurate shifting with the engine off so I know those are now correct. I opened the shift lever housing to inspect the teeth on the gear and found this picture below. Why is this oil so milky looking? I assume with oil like this I'll need to replace the wet clutch as well but am not positive. Does anyone have any input into how to flush this system and get things shifting correctly? Thanks in advance for all the help!

    • By BMurph
      Hi everyone. I am new here to the forum and am excited to learn from all of you with more experience than me with UTVs. Our Axis750 we use on the hobby farm started to have some issues going into gear. Yes, foot is on the brake and completely stopped as required with these machines. I thought it was the linkage and adjusted it to where it is accurately shifting with the engine off and key in the on position. I start the engine and it won't shift gears (yes foot is on the brake). I thought maybe it was the shift lever teeth so I opened the assembly and this picture shows what I just found. I assume this means the wet clutch would need replaced too while draining and flushing the oil. What else should I consider or be looking at? Any idea what could cause this? I don't see visible leaks or cracks in the system anywhere. Thanks in advance for the help!
       
       

×
×
  • Create New...