Quantcast
Jump to content


Recommended Posts

Posted

So, this unit comes in for hard to start, wont idle, and have to throttle and choke it to keep it running. Of course higher RPMs make shifting into gear awful.  It has the FD620D engine, 808 hrs, ranch vehicle but not abused. I rebuilt the carb, (the right way with dip soak and all the brass), replaced plugs, fuel filter, checked fuel flow from pump, dumped tank and put in fresh gas. It runs some better, but still wont idle or midrange without 1/2-3/4 choke. Very lean, but flowing good amount of fuel through main jets. I've checked for vacuum leak(s), and none found.

I have checked coils for proper resistance and found slightly above spec readings across primary terminals but secondary ok.  My query is, can the igniter box go out of "calibration" and change the timing on the coils and cause an advanced condition? The engine does "kick" once in a while when starting it. This could also cause the engine to seem to run lean.

Any suggestions are  greatly appreciated. I prefer that it be the "box" to change rather than the space-locked rear coil! What the hell were they thinking?!

Thanks in advance .

Dan

 

 

 

 

 

 

 

 

 

Posted

Its the way some engines react when timing is advanced too far. And if valves were out of time the engine wouldnt  run.  It runs pretty good with the "rich" condition it has with choke partially closed.

Posted

Any chance of swapping the carb with a known good running one? I know that you feel confident that's not the problem any longer. But it sure sounds like it's a carb issue. Since you've said it runs pretty good with the choke. Maybe some crud got missed, or a float, or jet problem causing this? From the description it sounds like a fuel issue. Can't help you on your specific question about the igniter box though.

Posted

Thanks for the thoughts. The funny thing is, even running for a short time with the choke partially closed, the plugs really soot up. That tells me its  getting more fuel than it can burn properly.  And these $275-300  carbs aren't a common inventory part.

  • Like 1
  • 2 weeks later...
Posted

Your symptoms sure sounds like the idle circuit in the carb is plugged or otherwise restricted.  The reason it runs a little better with the choke and/or partial throttle it because that's bypassing the idle circuit and you're running on the high speed circuit.  I would also check the float level.  That can cause excessive fuel (rich condition) that can cause sooting of the plugs and flooding of the engine.

Both conditions can cause hard starting and rough running engines.  Lesson I learned in high school auto shop long, long time ago before fuel injection was discovered.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
×
×
  • Create New...