Quantcast
Jump to content


Recommended Posts

Posted

So im in some desperate need for help with this dam buggy that im trying to put a limited slip diff from wavetrac or peloquin in without completely getting new axles for it. The transmission used in this buggy is the 020 trans which i currently have in pieces trying to rebuild and install the lsd. So the problems im running into are the axle shafts on the new lsd. The differential originally was a solid spool with 32mm splines with a ball plunging cv joint. The new lsd is a 27mm spline and i cant find a ball plunging joint/ axle flange that will fit with that so it can still obtain the plunging motion necessary and use the stock axles. I have taken pictures of the entire setup, im either looking for a flange that will work with the axles i have, or a cv that will fit my stock axles. Any help would be great, and appreciative. I just want to get this thing finished and its the last step. 657033d16cb865b24413fb9a955999c2.jpg313ff0bb03aa6f29120263ce294aa7b6.jpge6a76b442057cfb6c5ac77e071c0d05f.jpg603fcbd4fb66a8c0e790c440466e620a.jpgf7901c272cecc72f17d7cf37b02ebe18.jpg76c3da28fb850c3b7189db77b0aaad84.jpg90f4260bc00bf3b9330cbc16a166ac37.jpg1dae095431a1aa617136ccb5246afc4d.jpgce20e4bb50fef0e697f7833f4517d982.jpg

 

Sent from my SM-G955U using Tapatalk

 

 

  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • By CYJSP2009
      Dear Friends, 
      2022 Brand new Joyner CV Axles and CV  Joint rebuild kits are comming 
      1.  S650.03.02.02.00 ---Joyner 650 Commando Rear
      2. TR1100.03.01.03.00 --- Joyner Trooper Front 
      3. TR1100.03.02.03.00 --- Joyner Trooper Rear
      4. D650.03.02.02.00 --- Joyner 650 Sand Spider Rear Left 
      5. D650.03.02.03.00--- Joyner 650 Sand Spider Rear Right 
      6. SV800.03.02.01.00 --- Joyner 800 Viper, SV1100 Drive shaft Left
      7.  14274 --- 650 ider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      8. 15803  ---  650 Sand Spider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      Attached are the part photos for reference. 
      Above parts are now on the way to USA, will be ready for inland delivery in middle of July. 
      Price: CV Axle: USD250/ Piece;  CV Joint kit (without grease): USD110  send to door. 
      There will be special discount availabe for deals completed within July 2022.  
      Buy 1 piece: Get 5% discount, 
      Buy 2 pieces: get 10% discount.
      Buy 3 pieces: get 15% discount, 
      Buy 4 and more than 4 pieces: get 20% discount. 
      Please kindly note Qty for each part is not big  and it is hard to forcast when there will be next offer for these kind of products unless there is sufficient confirmed order qty for productioin arrangement. 
      Payment method: Payoneer payment link ( can pay through bank account or credit card) or Paypal ( [email protected]) .  Payment commission paid by the buyer. 
      Interested parties, please contact [email protected]
      Thanks
      Good Luck
      Casey / Leaf Asia
      July-07-2022
       
       
       














    • By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
×
×
  • Create New...