Quantcast
Jump to content


Neighbors mechanical problem.

baydog2

By baydog2
in UTV General Discussion

 Share

Recommended Posts

baydog2 Newbie

baydog2

Posted
Posted

Old guy that lives down the road is having a problem with his box side by side. It'll start and run for about five to ten minutes then bogs down and dies. It will not start up till it cools down and then it will start fine and do it again. Gauge shows not overheating and the oil and antifreeze is topped off. Any suggestions on what it can be? Just trying to help him out.

Dan B Community Regular

Dan B

Posted
Posted

Sound like a fuel starvation issue.  The next time is dies, immediately open the fuel tank cap and see it the engine restarts.  If it does, you might have a plugged or kinked fuel tank vent line.  That vent line allows filtered air into the tank to replace the fuel that was burned. If that doesn't do it, then someone smarter than I will have to help.  A friend had that problem with his small outboard motor.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


    • SteveS
      2021 Massimo MSU 800 will not run above 20 MPH
      By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • carl baney
      2021 Tracker 800sx DUMP BOX
      By carl baney
      have a 2021 tracker 800sx noticed locks on box when u fasten both sides of box are cracked anyone else have this probl
    • Frank Mac67
      AXIS 500 WILL NOT START. HELP!
      By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • Jim Kessell
      Predator 670 manual oil pressure gauge
      By Jim Kessell
      Hi All
      Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?
      Thanks in advance for your advice !!
      Jim

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...