Quantcast
Jump to content


Strike or Sector 250 wheels and tire options

CStrike250

By CStrike250
in Hisun UTV SxS Forum

 Share

Recommended Posts

strike250 Community Regular

strike250

Posted
Posted

Keep inind when you change your wheels to larger/taller ones, you effectively change the gear ratio. It might be quicker, but you'll loose top end. Also it takes more torque to turn larger tires, and these little ones don't have very much torque to begin with. The factory HP ratings are only around 10-12 HP from the factory. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Jon V
      reassemble Cub Cadet Challenger 700 - Crankshaft does not turn freely
      By Jon V
      Good afternoon. When the timing chain came off its lower gear (previous owner had over-tightened the tensioner), I ordered new parts.. chain, oil-pump chain, tensioner etc.. But now that it's time to put it back together, the main crankshaft makes a clang noise and stops when you turn it by hand. I want to solve this before assembling everything. The camshaft cover is off so that the valves aren't being activated. Should the transmission be in neutral to turn the crankshaft? The engine was running fine until the chain came off the lower gear. Then it would spin when the starter motor engaged so I assumed the crankshaft was spinning. Any advice is appreciated.
    • Greg Kilgore
      New AXIS 550
      By Greg Kilgore
      Was at Lowe's over the weekend. The wife and I seen they have a new Axis 550. That thing is sharp. Has a complete door. Speakers in door. Bigger engine. Bench seats. New styling all the way around. Looks to be more air tight than my 2022 model. I really like the looks but $10k is out of my price range for now. Unless I could sell mine. And the resale on the Axis 500 is nothing.
      Went to the local wally world today. See a 4 person Polaris General 1000 on the back of a trailer. That Polaris looked exactly like a stretched version of the Axis 550. Even down to the vents in the windshield.
      Just wondering if anyone can confirm or deny the Axis 550 is a copy of the Polaris?
    • diamondjfarm
      Good mornin' all. Just joined.
      By diamondjfarm
      I got an old 2003 Arctic Cat 375 Auto, and just bought a 2008 AC 650 side by side. Got a new starter, solenoid, and battery for the 650. Gonna change the crankcase oil and filter while I'm at it.
      Anything I oughta watch out for from them that's done the starter/solenoid on this model?
      Don't have a manual yet for the 650. Any recommendations for oil weight/grade?
      Thanks.
    • mac66
      Anyone have a Bad Boy Bandit?
      By mac66
      Apparently, these are Hisun or at least they use Hisun engines. I can't find much info on them online yet.  Ran across a used one with just 100 miles on it as a very reasonable price.  Just curious.
      Okay, more info...they are owned by Textron Corp who also owns Bell Helicopter, Cessna & Beechcraft aircraft, Ez-Go & Cushman and Arctic Cat and a bunch of other companies.
      So are thy cheap Chinese crap machines or are they good to go?
    • Alien10
      DIY front implement mount for Coleman Outfitter 550????
      By Alien10
      A while back I was looking at an auction UTV plow and the mounting of it.  Looked like it had an "H" bar with two pins that hooked into brackets on the front frame of the UTV.   I have a bunch of 1/4" x2" angle iron, and some 2"x1/2" flat stock in the barn.   I was thinking of welding up a bolt on implement mount that would provide 2 holes about 14" apart, that pins could be used to hook up an "H" frame for a plow or even a straight bar across with pins to hold it in place.   The angle iron "A" would utilize the existing bumper mounting bolts front and bottom, and have the two channels "B" with holes for individual pins or one large bar across. Those channels would be welded to the ends of the angle iron. 
      Anyone ever try this for a front mount?   It would be close to  this one that is for sale on the net.  It is supposed to fit a KFI plow mount.  

       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...