Quantcast
Jump to content


Recommended Posts

Posted

I had been wanting to install power steering on my T4 for years so I went to the salvage yard last weekend and bought a complete column (minus airbag) out of a 2009 Nissan Versa for $125 with the ECU.

It was a fairly simple install. The long shaft that fits to the Joyner steering rack actually fit perfectly into the Nissan column. Had to weld up a U joint on the Nissan column to make it a straight shaft and fab up one simple bracket. Connect power and ground plus a switched 12v and now I can steer with one hand!

91946288c74a5d990bad6a4da5bec532.png

 

  • Like 1
  • 4 months later...
Posted

I wouldn’t deal with SB...he is always a pain in the ass for some reason the few times that I have ordered parts from him and everyone on the forum that deals with SB reports problems receiving parts or just getting ripped off completely.

I will post some better pics as soon as I can, but I can tell you that the Nissan Versa column was simple to remove in the junk yard and the only additional parts I needed for installation on the Joyner was a 6” piece of 1/2” angle and 18” of heavy wire to run for power from the winch 12VDC connections.

Oh, and I did have to weld up a U joint that was part of the Nissan linkage, but it was easy!

 

  • 2 months later...
Posted

@mixfixdave  thanks for the pics, sorry for the late response. I hadn’t noticed you had responded back.  

 

Right now im having problems with my trooper it wants to stall when I give it gas. So I’m working on fixing that currently.

 

thanks again 

 

Scott

  • 1 month later...
Posted
Simply badass mixfix. Super impressed with your ingenuity. Guys like you are the heart and soul of the Joyner family. 

Thanks...makes wheeling the beast much more enjoyable.
  • 8 months later...
  • 9 months later...
  • 3 months later...
Posted

Hello guys, newb here. 

I own a 2004 Joyner Renegade R4 800cc and am wanting to add power steering to it and am wondering if the fix mentioned here would also work on my R4.

Thanks in advance for any help.

Kenny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
    • By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • By Tony P
      Twice my hisun has been driven a few miles and turned off back at home. Get back on it same afternoon and console is dead, no lights. 
      Have 12.7 vdc at battery and fuses are good. I hear relays click in the fuse box and main relay clicks but everything is dead. 
      Any ideas on what this may be? I've seen this problem before on this forum but it never finished. 
      Any help is always appreciated. Thanks in advance! 
       
×
×
  • Create New...