Quantcast
Jump to content


coleman 500 outfitter wont turn over


moparman48081

Recommended Posts

i have a coleman 500 outfitter 

engine will not turn over by using the ignition but will when you jump the starter silenoid 

also when it is running using this the battery is not charging 

i have replaced the ignition and starter sileniod still no difference 

near the passenger side wheel well area there was a wire with a plug that had a plug with resistor on it and the resistor is fried i havent been able to figure out a replacement part for it 

im hoping someone has some ideas on this 

20180928_113744.jpg

Link to comment
Share on other sites

  • 3 weeks later...

That appears to be a diode.  Can you see any labeling that might start with "1N".  That signifies a diode and no a resistor.  I'll see if I can find something online about it.  But maybe another Coleman owner or dealer can ID the part in the meantime.  A website I visited said that the Coleman may be a rebranded Hisun UTV.

Link to comment
Share on other sites

  • 1 month later...

Normally the only thing preventing the engine from starting is the brake lock out switch, some units need the parking brake to be applied to be able to start. Next would be the neutral selector switch. Some engines need to ensure the unit is in neutral to start. By the look of that connector, it might be a bypass switch of sorts. But start with the basics, check to ensure the parking brake does not have a switch on it more than two wires. Two wires will be needed to send the signal to the instrument to allow the dash light to come on letting you know the parking brake is on, if it has more than 2 wires, then its likely also working as a safety switch to prevent the engine from starting without the parking brake on. As for the neutral switch, it should have more than two wires, this has to be working for the engine to start. Although the dash light might light up, that doesnt mean the switch is fully operational. If the switch is faulty, then it will not send the signal to the starter relay allowing the engine to turn over.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By cindy koolness
      Can't find a starter for it at all. I have bought 3 and all of them were wrong. Please help me.. thank you
                         Cindy k
    • By Jon V
      Good afternoon. When the timing chain came off its lower gear (previous owner had over-tightened the tensioner), I ordered new parts.. chain, oil-pump chain, tensioner etc.. But now that it's time to put it back together, the main crankshaft makes a clang noise and stops when you turn it by hand. I want to solve this before assembling everything. The camshaft cover is off so that the valves aren't being activated. Should the transmission be in neutral to turn the crankshaft? The engine was running fine until the chain came off the lower gear. Then it would spin when the starter motor engaged so I assumed the crankshaft was spinning. Any advice is appreciated.
    • By Rick A
      I charged the battery reconnected everything but utv will not start and nothing comes on when key is turned. such as headlights, dash lights nothing.
    • By FGT
      QUESTION: How to wire the C/B into this current dual battery set up.

      EXISTING SITUATION: MAIN Battery is OEM and feeds OEM circuits. Added an AUX Battery in the OEM dual battery location. Connected the AUX - terminal to the MAIN - terminal. Connected the 100A Accessory Fuse Block power cable to the AUX + terminal. Installed a smart isolator between AUX and MAIN batteries where a cable from AUX + goes to the isolator and a cable from isolator to MAIN battery + terminal. Installed separate QD battery tender cables to both AUX and MAIN batteries + and -. The dual battery system appears to work as intended. For this Phase 1 improvement, to avoid having to constantly pull the leads on the AUX + battery post off and put on, for testing or maintenance of Accessory circuits, I wanted a more convenient and safer way to open the circuit from the AUX battery + terminal the Accessory Fuse Block. I called an off road dealership and was told to install a much larger capacity circuit breaker than the 100A rated Fuse Block and was recommended to get a 250A C/B like the one in the pic, which I did. I was told the reason for the C/B high amp rating was two-fold (a) to trip in the event of a battery short circuit and (b) to be able to conveniently open the C/B to kill power to the Accessory Fuse Block without removing leads from the AUX + terminal. The 250A C/B has two posts labelled "BAT LOAD" and "BAT LINE". There are currently three connections to the AUX + post: (1) Accessory Fuse Block power cable, (2) cable to Isolator AUX in terminal, (3) cable from AUX battery charger.


×
×
  • Create New...