Quantcast
Jump to content


Need advice on 4x4 Side by Sides


GoldToyBox

Recommended Posts

Looking to buy at a USED Side by Side.  Problem is I don't know that much about them but here is what I know.

I'm not a speed racer, it's low and slow for me but I need to get up and down some major hills.  We have used Yamaha Rhino's (450, 660 & 700) with good success on the ranch where we are hunting.  Kia. Mules need help getting up but The Honda Pioneer also needed help going up and are scary as hell coming down and dangerous in the mud coming down.  You are dead if you blow any of the corners.  The electric wouldn't go up the easy road, so the big hills are out of the question.  The Quads all do fine going up & down but I'm 70 yrs old and tired of muscling a Quad around.

I think what I need is a 4x4 with a high/low range shifter & locker (like the Yamaha Rhino has).  The Honda is so nice to drive but dangerous coming down hill with no low range, do the newer ones have it?  Trying to find info but hard to wade through it all.  So what am I looking for (besides a Rhino).

Lots of brands out there that I know nothing about: reliability?  prices?  HP, gearing, after market parts available, etc?  A few I never heard of before?

Thanks for any/all help/advise/thoughts/etc

 

GTB

Link to comment
Share on other sites

  • 2 weeks later...

I bought a used 2014 Joyner Renegade R2 with the 1100cc engine, cable select 4wd, front and rear lockers.  In 2014, they went from the 800cc engine to the 1100cc engine.  It has a clutch and 5-speed transmission with reverse.  1st gear is a "granny gear" max  speed is 12 mph in 1st gear.  As long as you can maintain wheel traction, that 1st gear might get you up some steep grades.  Max speed in 5th is about 60 mph (I've never had it over 40). It has about the same wheelbase as a Smart car.  So narrow off road trails might be a challenge.  Sounds like most of your riding will be in the <25mph range.  The maintenance support network isn't as extensive as some other brands, but it is out there.

I'm not a fan of the CVT transmission.  That's why I went with my choice.  Too many videos of belts coming apart (probably due to some hard riding)..  The John Deere 825i (and many other SxS) has the same 800cc engine.  It is a Chinese made Chery automotive engine used in many cars in South America, Asia and parts of Africa.  If the SxS you're considering has a 3-cylinder 800cc or a 4-cylinder 1100cc engine, it's most likely the Chery engine.

I have to admit that the CVT transmission is much simpler and easier to manage than my clutch/transmission set up.  You don't have to worry about gear selection or stalling the engine because of that.  Also, CVT transmission do a better job at keeping the engine within the best power RPM range.  One thing about CVT is that engine braking isn't available unless the engine is above idle.  That may be an issue coming down steep grades.  The engine doesn't grab the belt with the drive pulley until a certain RPM above idle is reached.

Is there a perfect SxS?  No.  But there is one that comes closer to your needs than others.  For me, my choice fits my needs.  I'm also 70 yrs old.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • By Brett
      Fuel injected 700 starts great and idles great but touch the gas and it dies
    • By Jeff S
      How to fix newer 800SX that gets stuck in LOW
×
×
  • Create New...