Quantcast
Jump to content


2018 Coleman UT400 Trans keeps popping out of forward

dman66

By dman66
in Coleman UTV SxS Forum

 Share

Recommended Posts

dman66 Newbie

dman66

Posted
Posted

My buddy has a ut400 that the forward gear keeps popping out of gear. She only has like 400 miles on the odometer .the shift cable has been adjusted and the shift lever has been updated / modified. All other gears are good. Is there an internal detent cam or something that wears out or shift fork that can be replaced ? Or is there some other magic that I can perform ? Looks like the engine needs to be split.

  • 4 weeks later...
Alien10 Explorer

Alien10

Posted
Posted

THis might not be related.  I have a 550 UTV and I use primarily the low forward gear.  This means the shifter must be pushed fully upward.   I noticed that there is a very slight "click" and a final movement if I hold the shifter all the way up as I begin to move the UTV.  As if it is not quite fully engaged without that last extra push as I give it a little gas.   I also found that some UTV dealer (Hisun/Coleman dealer) had a video pointing out this very same thing.   Like I said, may not be the problem you have. Good luck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Coleman UT 400 Garage?
      By Homeowner A
      I have a Coleman UTV 400 and looking for something to store it in.  Preferably something vinyl or plastic with its own base that can stand alone outside and house the UTV.  I think the dimensions of the UT400 are around 106" long 52" wide and 74" tall. 
      What should I consider that won't break the bank?    
    • Justine
      Hisun Vector E1 - Gear oils
      By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • Will Sutton
      Coleman UT400 won't rev. Idles fine
      By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.
    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • shawn b
      2020 hisun 400 utv side by side
      By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...