Quantcast
Jump to content


Hitch Extender Cub Cadet 2016 Challenger 700

TomWA

By TomWA
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

TomWA Contributor

TomWA

Posted
Posted

2016 Cub Cadet Challenger 700 has a hitch receiver that requires a vertical pin as opposed to a horizontal pin to attach hitches.  I'm looking for an 18" hitch entender that will attach using a vertical pin and then accept a horizontal pin for a trailer hitch.  I've looked everywhere.  Any ideas on where to find one?  TIA

  • 6 months later...
  • 5 months later...
JVR1330 Newbie

JVR1330

Posted
Posted

That's we ended up doing on our 2017 Cadet Challenger 700.  I looked all around for a vertical pin hitch to fit and to no avail (I guess things are different in China) - so I just drilled a vertical hole in my hitch - works great ; )

 

  • 2 months later...
Overlander Rookie

Overlander

Posted
Posted
On ‎3‎/‎13‎/‎2020 at 4:18 PM, TomWA said:

I found a hitch extender online with a vertical pin.  See below.  It could be cut shorter, but I needed one to extend past the bed.

hitch extender.jpg

Do you have a link for the extender? Has it worked out ok for you?

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Steve Waldner
      Looking for a Kioti Mechron 2200
      By Steve Waldner
      Looking to buy a Kioti Mechron 2200
    • Croppy38
      Challenger 750 flywheel issue
      By Croppy38
      I own a 2017 Challenger 750 and had the key way snap at the flywheel. It was removed and cleaned up and then the  flywheel was put back on with a new keyway. It snapped a second time so the flywheel and keyway both were replaced. They both seem to fit nice and tight. Put it all back together and it snapped again. I have no idea why it is doing this. 
    • Bloodhound
      2016 can am commander
      By Bloodhound
      Don't know the size anyone know the reliability fo theae

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...