Quantcast
Jump to content


2009 Joyner Trooper that cuts out when it warms up

nascarcamshaft

By nascarcamshaft
in Joyner UTV SxS Forum

 Share

Recommended Posts

nascarcamshaft Rookie

nascarcamshaft

Posted
Posted

I have a 2009 Trooper that when I first start it it runs great but after about a min it starts to cut out under acceleration but clears out when it gets revved up.  I downloaded the manual from   Joyner-usa.com   but it doesn't help much,  Mine doesn't have a OBD port on it and my son who is a mechanic said he can wire one in if we have a wiring diagram for the CPU but the wiring diagram of the CPU that is in the manual is for a 3 cylinder engine.  The manual talks about a MIL light that can flash out a code but I don't know where that is and even if I did find it they  don't tell me how to read it.  I have tried the coil and the map sensor and that didn't help I checked the TPS and it checks OK.  I emailed Joyner and all I got from them is there should be a OBD port on it and then they said they checked and found some don't have it,  No help from them. Anybody run into this problem or know were I can turn to get some help on this, even a good wiring diagram of the CPU would be a big help.

Thanks for you help

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Ridge Runner
      2019 Coleman 550 Outfitter, need help accessing tail gate latch screws
      By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • Woody77
      Stator replacement an now want start
      By Woody77
      UTV MASSIMOREPLACED STATOR WANT start replaced rectifier still want start stator ohms out 5 ohms each leg what could be wrong at this point 
    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • Tony P
      2020 Hisun utv No power on console, no start...dead
      By Tony P
      Twice my hisun has been driven a few miles and turned off back at home. Get back on it same afternoon and console is dead, no lights. 
      Have 12.7 vdc at battery and fuses are good. I hear relays click in the fuse box and main relay clicks but everything is dead. 
      Any ideas on what this may be? I've seen this problem before on this forum but it never finished. 
      Any help is always appreciated. Thanks in advance! 
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...