Quantcast
Jump to content


Recommended Posts

Posted

Hi, I'm getting ready to supercharge my trooper and I'm looking for advice on the setup. So far I have... a AMR500 supercharger, small intercooler, Dolbeck EJK fuel controller and wideband. Looking for any advice on what else I'm going to need and what to expect..Thank you

 

 

 

Posted

Thanks! This is exactly the type of thing I'm looking for advice on! Do you know the specs of the one I'll need?  Would it be a 5v 1w? Also from the 1100 service wiring diagram it showed 1 is pressure signal 3 is temperature signal and 4 is ground.. And  the first diagram shows the diode between signal and ground. So I'm guessing the diode  goes between 1&4 and not 1&3 like you Drew on the paper...?

  • Like 1
Posted
Thanks! This is exactly the type of thing I'm looking for advice on! Do you know the specs of the one I'll need?  Would it be a 5v 1w? Also from the 1100 service wiring diagram it showed 1 is pressure signal 3 is temperature signal and 4 is ground.. And  the first diagram shows the diode between signal and ground. So I'm guessing the diode  goes between 1&4 and not 1&3 like you Drew on the paper...?
Yes been so long ,5v 1w works ,think your right 1-4 , I also got a field controller from dobeck but I had them max out to 12millisec or the longest pulse available " been couple years hard to remember "
Running a gt15 turbo seems to work fine

Sent from my SM-G930W8 using Tapatalk

  • Like 1
Posted

Ok cool! Seems I'll be basically replicating something similar to your setup just supercharger instead of Turbo, until I can go megasquirt later like Lenny(hopefullywhen i have more money)!... So if you could run down everything you had to make it work, I'd appreciate it..  Did your dobeck have a  vac/boost line.. Because I've seen ones with it and I have the one without it... Also did you have to go water/meth injection or 100 octane anything like that.. Thanks..

Posted
Ok cool! Seems I'll be basically replicating something similar to your setup just supercharger instead of Turbo, until I can go megasquirt later like Lenny(hopefullywhen i have more money)!... So if you could run down everything you had to make it work, I'd appreciate it..  Did your dobeck have a  vac/boost line.. Because I've seen ones with it and I have the one without it... Also did you have to go water/meth injection or 100 octane anything like that.. Thanks..
Forgot went to ejk after 1st programmer broke
Used these setting for basic setupd1906ade94a28b10a5e1a476db2723b0.jpg

Sent from my SM-G930W8 using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By Bloodhound
      Any info on the duribility and reliability of these  don't know the size
      And also 2006 rzr duribility and reliability 800cc
    • By CRV
      I’m need a couple parts. Diff. Lock Actuator mainly. But I would like to find a donor that maybe has bad motor or something along those lines. 
      if anyone has or knows of anything please holler at me 
      thanks Randy 
    • By CRV
      Howdy new member here . My hobby's Rabbit dogs , gamefowl . I'm retired from my real job but I stay busy with the hounds and gamefowl . So to help around the farm I ran across an old 2007 CC Big Country 4x2 to haul feed , water , sprayer and my sorry a$$ .It is in pretty good shape , 781 hrs. good plastic , tires, ect. . But as anything outside and 18 years old it needs seats ! The thing I have found wrong mechically the Diff. Lock Acturtor is broken where it mounts to the bracket ( partly why Im here ) . Hoping someone here can help  ! Just my wish list but Id like to find a roll cage and a composit/plastic top for it Im thinking I'll need a donor to salvage these things from ( again partly why Im here ) .Is there another brand that uses this same actuator? If anyone reads this and has or knows of any of threse parts PLEASE HOLLER !! 
      Again Howdy brothers & sisters

    • By weasel
      starts up you have keep rpms up for 5 minutes till it warms up then runs fine. But if it stalls wont start unless you unplug fuel pump and hold it to the floor till it starts then plug pump back in and run it till it warms up then it is fine all day.
×
×
  • Create New...