-
Similar Topics
-
By camojay
When we first heard the noise, we immediately stopped driving it...at first we thought it might be a linkage issue, but after further inspection looks like the sound/jolting is coming from the rear diff. Took a video below...
Anyone know what is creating the diff to skip/jump like this? We drained the diff oil and didn't look terrible, no metal.
Other info that may be useful:
1400 miles on it
Recently tightened the E brake
P.s. never posted on this forum before, let me know if the video does not work
20240817_133539_1.mp4
-
By CRV
Howdy new member here . My hobby's Rabbit dogs , gamefowl . I'm retired from my real job but I stay busy with the hounds and gamefowl . So to help around the farm I ran across an old 2007 CC Big Country 4x2 to haul feed , water , sprayer and my sorry a$$ .It is in pretty good shape , 781 hrs. good plastic , tires, ect. . But as anything outside and 18 years old it needs seats ! The thing I have found wrong mechically the Diff. Lock Acturtor is broken where it mounts to the bracket ( partly why Im here ) . Hoping someone here can help ! Just my wish list but Id like to find a roll cage and a composit/plastic top for it Im thinking I'll need a donor to salvage these things from ( again partly why Im here ) .Is there another brand that uses this same actuator? If anyone reads this and has or knows of any of threse parts PLEASE HOLLER !!
Again Howdy brothers & sisters
-
By mhill
I purchased a 2008 American Sportsworks Subaru TW265 UTV, with no manual and no previous knowledge. When idling, the steer column shakes uncontrollably, is very noisy, and might be from vibrations from the engine. Logically, I am thinking engine vibration moving up the steering column. I found a schematic, but that has not helped in identifying the specific problem.
Any thoughts? Suggestions?
Thanks so much
-
By weasel
starts up you have keep rpms up for 5 minutes till it warms up then runs fine. But if it stalls wont start unless you unplug fuel pump and hold it to the floor till it starts then plug pump back in and run it till it warms up then it is fine all day.
-
-
By staind
Looking for information on installing a OBD port or a lite to read codes in ECM.
I can not find a OBD port or a lite to read codes on this R2 with 800cc.
I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking.
This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
I want to know what the ECM is reading to help dio it.
This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever.
thanks Dan D. aka staind
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.