Quantcast
Jump to content


Tracker 800SX sway bar

Paul in Wisconsin
 Share

Recommended Posts

Paul in Wisconsin Newbie

Paul in Wisconsin

Posted
Posted

I have a 2023 Tracker 800SX LE that I want to add a sway bar to.

The service manual shows how to remove and reinstall the sway bar.

I called Cabela's to try and get the saw bar.   They said they can't get one and the 800SX doesn't have one!!??  Then why is it listed in the service manual?? No answer from them.

Have any of you found a saw bar that fits and what did it cost?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Cory J
      2023 t-boss 550 belt slipping and found oil in belt housing
      By Cory J
      Belt started slipping when I used it in high gear. It works okay in low unless I'm trying to power it up a hill and then it slips.., Ordered a new belt and went to change it and found a good bit of oil in the belt housing. Has anyone experienced this? Belt looks fine. Only have 300 miles on this thing..
    • Gerald Mohs
      2023 massiso T-boss 750 cam sprocket removal
      By Gerald Mohs
      Is the cam sprocket a bolt removal or is it pressed on? Dang bolt is on tight. Impact wrench won't even move it.

    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • Gerald Mohs
      2023 massiso T-boss 750
      By Gerald Mohs
      Have a 2023 massiso T-boss 750 stopped one day and won't start. I've checked the fuel injector and has good spray. New spark and has spark. Need advice on getting the trouble codes. What code reader do I need to purchase? Thanks for any help. Jerry 
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • Gary Gallo
      2022 tracker 800sx help
      By Gary Gallo
      Just wondering if anyone has had problems with bed warping coming from the heat from the muffler.. If I ride more than 5 minutes my bed starts warping from the heat.. Does anyone have any recommendations on what wrap or shield I can get to prevent this before my bed starts cracking or the warping becomes permanent.. I only have about 50hrs on the UTV.. Basspro said they haven’t had this problem from anyone else.. Hard to believe..

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...