Quantcast
Jump to content


2017 Intimidator XD4 800 Check Engine

Reynolds Rocket

By Reynolds Rocket
in Intimidator UTV SxS Forum

 Share

Recommended Posts

Reynolds Rocket Newbie

Reynolds Rocket

Posted
Posted

I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 

Link to comment
Share on other sites
  • Alex changed the title to 2017 Intimidator XD4 800 Check Engine

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Jim Kessell
      EH65 spitting fuel from breather hose into air filter.
      By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • Will Sutton
      Coleman UT400 won't rev. Idles fine
      By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.
    • John M in Louisiana
      Hisun E1 Power Plug Replacement
      By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • Brett
      2006 Polaris Ranger 700 side by side idles fine but dies when you touch the gas
      By Brett
      Fuel injected 700 starts great and idles great but touch the gas and it dies

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...