Quantcast
Jump to content


2021 Hisun Axis 500 No Start - Need Help Please

Hunterman22

By Hunterman22
in Hisun UTV SxS Forum

 Share

Recommended Posts

Hunterman22 Newbie

Hunterman22

Posted
Posted

2021 Hisun Axis 500 UTV (From Lowes)

Will NOT START

MY apologies if this is to much info just wanted to give yal the most information possible for help.

I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 

I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 

So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 

Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 

So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 

Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.

So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.

 

 

Steve G. Apprentice

Steve G.

Posted
Posted

Kinda sounds like some kind of fuel starvation. Possibly clogged lines or fuel pump or maybe the injector. Try disconnecting the fuel line from the injector body and put it in a large container to catch the fuel. Crank it over and see how much fuel your getting. Of course be very careful when doing this and just a few seconds should show you if enough fuel is coming out. If that looks good I'd suspect the injector.

  • Thanks 1
Hunterman22 Newbie

Hunterman22

Posted
  • Author
Posted
10 hours ago, Steve G. said:

Kinda sounds like some kind of fuel starvation. Possibly clogged lines or fuel pump or maybe the injector. Try disconnecting the fuel line from the injector body and put it in a large container to catch the fuel. Crank it over and see how much fuel your getting. Of course be very careful when doing this and just a few seconds should show you if enough fuel is coming out. If that looks good I'd suspect the injector.

Thank you Steve G. Its 9:20pm wher I live & I'm just now seeing you're reply ,so I definitely try that tomorrow & let you know the results. 

  • Alex changed the title to 2021 Hisun Axis 500 No Start - Need Help Please
cryptkeepr99 Newbie

cryptkeepr99

Posted
Posted

I'm sorta having the same problem, have a 22 hsun 400, was running and plugged 1 of those small air compressor to air up a tire, about a minute later it just died on me, will turn over but won't crank, only found 1 fuse and it doesn't look blow, so i have no idea what's going on, any help is appreciatede

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • Frank Mac67
      AXIS 500 WILL NOT START. HELP!
      By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • bms stallion owner
      BMS UTV sluggish acceleration issues/ final gear oil maintenance concerns
      By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks
    • Alien10
      Coleman (or Hisun) Parts and Service experiences.
      By Alien10
      Maybe members can post where they have obtained parts and service for their Hisun produced UTVs and ATVs, including the Coleman lines.  Maybe post the model you have, what you bought,  and how the products were quality wise.  Also if you had any shop service done, where (city & state) and how it worked out for you.   
       
    • Greg Kilgore
      2021 Axis 500 Head Bolt Torque specs
      By Greg Kilgore
      Got a 2021 Axis 500.
      I'm needing the head bolt torque specs.
      Manual states 38nm.
      But saw a video Hisun put out on YT for a 550 stating 50nm + 45° turn of wrench. Didn't think they would be that much difference on a 500 and a 550.
      Seen another YT video on a 2013 500. He did 38nm.
      Really only want to do this job once and done. And done correct.
      Anybody got the answer?
      Going to start this rebuild in a few once this weather brakes. Flooding and then snow and cold here now. But spring is around the corner and the wife has to have this fixed or a Honda pioneer may be parked in driveway soon. She has to be able to ride.
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...