Quantcast
Jump to content


2021 Hisun Axis 500 No Start - Need Help Please

Hunterman22

By Hunterman22
in Hisun UTV SxS Forum

 Share

Recommended Posts

Hunterman22 Newbie

Hunterman22

Posted
Posted

2021 Hisun Axis 500 UTV (From Lowes)

Will NOT START

MY apologies if this is to much info just wanted to give yal the most information possible for help.

I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 

I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 

So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 

Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 

So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 

Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.

So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.

 

 

Link to comment
Share on other sites
Steve G. Apprentice

Steve G.

Posted
Posted

Kinda sounds like some kind of fuel starvation. Possibly clogged lines or fuel pump or maybe the injector. Try disconnecting the fuel line from the injector body and put it in a large container to catch the fuel. Crank it over and see how much fuel your getting. Of course be very careful when doing this and just a few seconds should show you if enough fuel is coming out. If that looks good I'd suspect the injector.

  • Thanks 1
Link to comment
Share on other sites
Hunterman22 Newbie

Hunterman22

Posted
  • Author
Posted
10 hours ago, Steve G. said:

Kinda sounds like some kind of fuel starvation. Possibly clogged lines or fuel pump or maybe the injector. Try disconnecting the fuel line from the injector body and put it in a large container to catch the fuel. Crank it over and see how much fuel your getting. Of course be very careful when doing this and just a few seconds should show you if enough fuel is coming out. If that looks good I'd suspect the injector.

Thank you Steve G. Its 9:20pm wher I live & I'm just now seeing you're reply ,so I definitely try that tomorrow & let you know the results. 

Link to comment
Share on other sites
  • Alex changed the title to 2021 Hisun Axis 500 No Start - Need Help Please
cryptkeepr99 Newbie

cryptkeepr99

Posted
Posted

I'm sorta having the same problem, have a 22 hsun 400, was running and plugged 1 of those small air compressor to air up a tire, about a minute later it just died on me, will turn over but won't crank, only found 1 fuse and it doesn't look blow, so i have no idea what's going on, any help is appreciatede

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • shawn b
      2020 hisun 400 utv side by side
      By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated
    • TPlummer
      Axis x550 02 sensor on right after buying the UTV.
      By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • Chucky 1
      DO NOT BUY A LANDMASTER UTV!!!!!!
      By Chucky 1
      I purchased a new 2023 Landmaster UTV L4 in October of 2023.  UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better.  After about a week the unit started bogging down backfiring and stopping.  Gas fumes really bad, wait a few minutes and it would start up again.  Brought it back to the dealer and after keeping it for a few weeks said he couldn't find anything wrong with it.  Got it back home and it started acting up again, brought it back to dealer a week later and he said he found couple things that might cause it to do run bad and he was able to replicate the issue but didn't really know what was wrong.  Got it back home again after being at dealer for several weeks and the unit started running bad again right away.  Brought it back to dealer and he went back and forth with Kohler about possible fixes but just checked somethings and try to swap a few parts but still runs bad.  I called Landmaster HQ to speak with someone about a refund and was told that was handled at the dealer level.  Dealer called Landmaster and they told him they didn't do refunds or exchanges especially with units that had problems.  The dealer is now trying to get a new engine to but I have not heard anything as of yet.  I did file complaint with Better Business Bureau and they accepted my claim and reached out to Landmaster.  The National Service Manager called me and said the he had been contacted by the BBB about the complaint and he would look into it.  I told him that I would just like to have my down payment of $2,000.00 returned and never mind the over $1,000.00 I have paid in notes for a UTV that I cannot even ride on without hoping it gets me around the neighborhood.  I have found out that the 2024 Landmaster UTVs will have Vanguard engines due to issues with the Kohler engines.  Very disappointed in what is "Proudly Made in the USA" and the way Landmaster has treated this disabled veteran! 
    • PossumTruck
      Lower Radiator Hose ID - UTV 400
      By PossumTruck
      Greetings,
      I have a client that wants me to install a heater of some sort to aid in cold weather starting (she uses it at her business, has had issues starting the last few days in sub-zero). I would prefer a coolant heater to a pan heater (silicone pad), but I cant for the life of me find the diameter of the coolant hoses. Heck, I'm not even sure if it would work as well in this application given how long the hose is compared to tractors and trucks I have installed them in. 
      Any advice you could give me would be GREATLY appreciated. 
    • Solution For That Pollution
    • Greg Kilgore
      Heater installed 2021 Axis 500
      By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...