Quantcast
Jump to content


Temp Sensor Resistance Cold HS800 EFI (2014)

etimc

By etimc
in Hisun UTV SxS Forum

 Share

Recommended Posts

etimc Rookie

etimc

Posted
Posted

I suspect I have a faulty temp sensor but at the cost of the sensor plus 50 percent tariff plus the shipping cost to Costa Rica, i would like to confirm it - the Hisun 800 has 2 sensors - one in the radiator appears to be a fully open or fully closed bi-metal contact switch similar to the old household thermostats for your heating system. - My fans turn on and off automatically as they should and a jumper across the connector also triggers the fan - appears to be a simple logic circuit back to the computer that then trips a relay for the fans.  The second sensor is on the back cylinder almost hidden by the throttle body and idle control system - I have unplugged it, sprayed it with contact cleaner, checked the pins, tried to get a resistance reading across the sensor, reconnected it and still get a blinking red light on the display panel warning of high temperature - this occurs even when the buggy is still cold having just started it in the morning - I have not been able to trace out the other end of the cable on the display panel since it appears i will have to remove the entire front plastic to get to it - hoping i could confirm the resistance before i go to that step (this is the same buggy originally posted by Jim Magnuson last September when the spark arrestor overheated and burned the plastic pickup bed - I fixed that by removing and cleaning the spark arrestor and it has never glowed red again.  I would really like to put a guage in place of the digital idiot light since (from experience in automobiles) by the time the idiot light goes on you have already damaged the engine - Which brings the second question - would it be advisable to swap the front radiator sensor for a real sensor and then jumper the fans to always on condition at the connector so the computer contentedly thinks everything is working and it is doing its job ?

 

etimc Rookie

etimc

Posted
  • Author
Posted

More reading and research and I guess it appears that both sensors are full make/break contact switches and a third sensor in the MAF/MAP/Temp sensor is the one that is variable resistance - sooo - if my dash light is always on for overheat condition, then i guess i need to follow the wire and find where it might be grounding out.

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Homeowner A
      Black O2 Sensor?
      By Homeowner A
      I've been having misfire issues with my UTV 400 when it gets warm and I've thrown all kinds of parts at it so far with no permanent resolution.  Today I removed the O2 sensor and it is black on the end.  To me that means it's running rich and/or the sensor isn't working.  I replaced the sensor with a new one and will see how it goes I guess.  With EFI, I'm wondering why the sensor would be this way with low hours and mileage?  Is there a way to adjust or lean out fueling on these?  Thanks in advance.  
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...