Quantcast
Jump to content


2006 kohler powered cub cadet volunteer

alywiski

By alywiski
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

alywiski Newbie

alywiski

Posted
Posted

I just recently picked up a 2006 volunteer.  It is making a grinding noise that seems to be coming from the clutch or around there.  Sounds like a bering going out.  Trans goes into gear good and it drives good just makes the grinding noise at higher rpms and gets loud as soon as you pull you foot of the gas.  Does anyone know what could cause this or what i need to replace? thanks 

  • 1 year later...
T Hudson Newbie

T Hudson

Posted
Posted

Hello Alywiski, you might be able to help me.  I have a 2006 cub Cadet with diesel engine.  The diesel went out and would like to replace with a gas engine.  Can you tell me what size and model Kohler engine is in your UTV.  Replacing the diesel engine would run about $7,000.00.  Replacing with a Kohler gas engine may be $3000.00 at the most.

Thanks T Hudson 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.
    • bms stallion owner
      BMS UTV sluggish acceleration issues/ final gear oil maintenance concerns
      By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...