Quantcast
Jump to content


Recommended Posts

Posted

Recently, my unit Axis 500 (2020) will only go into reverse and neutral. I am not able to get high or low. The engine itself sounds fine and I do not have other issues on this unit. I change the engine oil but have not yet changed the gear oil.
Before this happened I occasionally encountered issue where going from reverse to high gear, it would grind some and i had to reposition to shift into high gear. I also for last couple weeks heard a squeaking sound. I couldn't tell what it was. Was looking for a grease point I missed.
The unit has around 70 hours and is kept in the garage.

Anyone else encounter this type of scenario? Any suggestions on troubleshooting would be appreciated. Thanks.

Posted

Have you checked the cable adjustment.

When shifter is in neutral, is the neutral light lit on dash. And is the trans actually in neutral. 

Same question for reverse?

How far does the shifter move when trying to go from neutral to forward.

I'm sure you are pressing the brake when trying to shift into a forward gear.

Posted

My 550 is also difficult to shift but more often into reverse.  I find that hard on the brake sometimes will let it move easier into reverse.  These cable driven shifters are not exactly great that's for sure.  Is the idle set too high?  Might check that if it moves at all when you do get it into gear.  

Posted

Thanks Greg, when in reverse, it does light up reverse on the dash. When in neutral it lights up as reverse on dash. When in high, it lights up as neutral. It seems like it might be going farther forward but I am not positive.

Yes, brake is applied when shifting. 

When I shifted to what should be high gear and it lighted up as neutral, and then, when I applied the gas, it was indeed in neutral and did not move. In reverse, the unit moves in reverse as expected.

Posted

Thanks Alien10, as yet, I have not checked the idle, by listening, it seems pretty consistent as far as idle but maybe...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By boydog40
      my subaru gave it up, bought a new Predator 670cc
      problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
      new motor has many more wires than the Subaru and i have no idea what goes where!!!
      finding any info on the web is almost impossible to do also
      any help will be greatly appreciated!
      thanks guys
    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Jerrys500
      Hi I'm about to order parts to do a bunch of work on my Massimo. Does anyone know if there's a difference in the top end kit {piston, Cylinder, Rings, Gaskets, Piston Pin} if it has a carb or EFI? I'm EFI and I think some came with a carb so I thought i'd ask before making a mistake...
      Thanks Jerr
    • By Homeowner A
      Picked up an essentially new 2022 UT400 with 9 miles on it.  Decided to change the oil because it's probably never been done.  Pulled the dipstick and noticed it was overfull then went and pulled the drain plug and took off the filter and it was like brown water running out.  What should I start checking?
    • By Robby
      Hello, I have a 2013 500 utv hisun. Was running ok and cut out while parked. Bike will not start now. It turns over, but won't fire. I have no spark and no fuel. I replaced fuel pump, ignition coil, spark plug, cdi, voltage rectifier and all the fuses and relays. Could bad stater cause no fuel because I can't hear the fuel pump priming. Any info on where to start looking for problem.
×
×
  • Create New...