Quantcast
Jump to content


Help with Limited Slip

GDS

By GDS
in Other UTV SxS Forum

 Share

Recommended Posts

GDS Explorer

GDS

Posted
Posted

I have a Brush Hog TH420 side by side and having trouble with spinning one tire. The other tire will kick in but only after you spin like hell and dig a hole. The final drive /gearbox is a Comer Industries out of Italy. The part number is 9.485.003.00, SN 0082, Date is E04.  I can find a parts breakdown. When you bring up the transaxle it shows the internal differential but no breakdown. It does say see diff assembly but there is no diff assembly.  I'm not sure if this type is no some other side by side. 

0715191459.jpg

vaughn Enthusiast

vaughn

Posted
Posted

With the older cars with limited slip rear ends you had to use certain fluid. It might be the cause of your problem.  Has it ever been changed?  How many hours, miles since the last change?           Manual says to use and change the transaxle fluid.                                                        Mobilube HD LS 80W-90  (or equivalent)                                                                                                                                                                                                                                         https://www.manualslib.com/manual/878997/Bush-Hog-Th420.html?page=54#manual

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • rdborra
      Bobcat 2200 dump bed relay pops fuse and stalls after warm
      By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
    • mcraigchr
      550 - Diff fluid change and final drive?
      By mcraigchr
      Howdy y'all,
      I have the service manual, but it leaves me with questions.
      1)  It is time to change the diff fluid.  The service manual says 80w-90 for the rear and Dextron 3 ATF for the front!  Is that correct?  That seems odd to me.
      2) The service manual also speaks of the need to change the transmission fluid but gives no detail about it.  What needs to happen here?
      3). The service manual also discusses changing the final drive fluid with 80-90 Hypoid.  Is the final drive actually the tranny?
      Any details about the changing of the fluid or what fluid to use ... or even other things that need to be changed that the manual does not mention would be appreciated.
      Thanks,
      Craig C.  
    • bms stallion owner
      BMS UTV sluggish acceleration issues/ final gear oil maintenance concerns
      By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...