Quantcast
Jump to content


UT400 cutting out mid throttle

Homeowner A

By Homeowner A
in Coleman UTV SxS Forum

 Share

Recommended Posts

Homeowner A Contributor

Homeowner A

Posted
Posted

Have an issue all the sudden where the UTV will cut out randomly mid range throttle and under load.  Light consistent throttle on fairly flat ground no problems.  If you quickly change throttle position sometimes it will bog down and cut out, splutter, etc.  Floor it or let off and it may do just fine.  Going up a hill and adding more throttle as the incline demands, will cut out splutter and smell unburnt fuel.  So far doesn't ever completely quit.  If you let off it will idle just fine.  A lot of times if you floor it, it will pick up and even get a boost of power.  Changed to a slightly hotter plug to see if that would make a difference, but it didn't .  Any ideas what might be going on and what to try next?  

  • 3 weeks later...
Homeowner A Contributor

Homeowner A

Posted
  • Author
Posted

Replaced injector and it has been running well until yesterday. Now it’s cutting out again mid throttle when it gets up to full temp. Possibly misfiring too did smell some unburnt fuel at one point when it would cut out.  Light throttle or flooring it and it does fine. I replaced the injector again but no improvement. Any ideas? What should I look at next?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • CSM_Retired
      Kioti UTV SxS Forum
      By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • Edelbrock
      What UTV should I buy?
      By Edelbrock
      So I'm interested in a side by side of some sort.
      Not sure what make/model to even look at.
       
      I would plan on riding on trails with very rough rocky terrain and plenty of mud. Maybe sand once in a long while. I like LOTS of power and drive fast, but also like a trail that is a challenge to get through. I think 4x4 would be a must. I like the idea of a supercharged engine, but I have never owned one, and would be a little concerned about long term reliability or expensive difficult engine repairs. If anyone knows quads, my favorite was the 2008 Polaris Outlaw 525 IRS. For dirt bikes, I raced a 2008 KTM 450 SX-F. So that gives you an idea of what type of off road stuff I liked.
      I don't like "utility quads" or "trail bikes". And likewise, I dont want a turd UTV. I want something that looks awesome and performs awesome. 2 seater with some cargo capacity at the minimum.
       
       
      Thoughts?
    • Tom Gorski
      2014 Cub Cadet Volunteer Oil Change
      By Tom Gorski
      Just bought a 2014 Volunteer. Can anyone tell me what parts have to come off to change the oil and filter. I can see them but I can't figure out how to access them. Thank You
    • Pick a name
      Shifting issue
      By Pick a name
      The Axis 500 will not shift into low or reverse.  I have high when it should be in low and all the other places it is reverse.  The gears in the shift cover are fine and I shifted it when the cover was off and yet no change (so it can't be the shifting mechanism gears).  I t has been difficult to get it into low for awhile.  But now it is either high or reverse, no neutral either.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...